12/24V invertori un invertori-lādētāji

Specifications

Dimensions: 360 × 240 × 100 mm

Weight: 7.50 kg (net weight 6.50 kg)

Model: MultiPlus 12/800/35

Voltage: 230 VAC / 12 V

Protection class: IP21

Certifications: ECE R10-5, EN-IEC 60335-1/-2-29, EN 62109-1, EN 55014-1/-2, EN-IEC 61000-3-2/-3-3/-6-1/-6-2/-6-3

Information

35 A battery charger with the POWER ASSIST function, which extends the capacity of the alternative power source. During peak load, the battery charge is automatically reduced to prevent overload, and the required power is drawn from the battery. When the load decreases, the excess current is used to charge the battery.

The NO BREAK feature ensures an uninterrupted power supply. Up to six Multi devices can be operated in parallel for higher power output, while three devices can be configured for a three-phase system.

4-stage charging system and dual battery charging

Powerful charging with customizable charging software optimizes the automatic three-stage charging process based on the battery's condition and adds a fourth trickle-charging mode for extended operation.

High starting power

Suitable for devices with high inrush current, such as LED lamps, halogen lamps, and power tools.

SEARCH MODE

Power consumption is reduced by approximately 70% when there is no load. In inverter mode, the device shuts off when the load is very low and briefly activates every two seconds to check its status. If a sufficient load is detected, the inverter continues to operate.

Programmable Relay and Remote Control

The relay can be used as an alarm relay. System configuration, monitoring, and control are available via the web. The device is ready for use immediately after installation. The battery charging voltage and SEARCH MODE can be adjusted using DIP switches.

Inverter Specifications

Input: 9.5–17 V DC
Output: 230 VAC 50 Hz
Maximum power: 1600 W
Maximum efficiency: 92%
No-load power consumption: 7 W (2 W in SEARCH MODE)

Charger Specifications

Input: 187–265 VAC
Output voltage:

• 14.4 V (absorption)
• 13.8 V (float)
• 13.2 V (storage)

Charging current:

• Main battery: 35 A
• Starting battery: 1 A

Includes a temperature sensor.

General Information

Built-in 150 A DC fuse.
Protection against:

• short circuit
• overload
• battery voltage that is too high or too low
• overheating
• 230 VAC at the inverter output
• excessive voltage ripple

Communication port: VE.Bus

Operating temperature: -40 °C to +65 °C

Maximum relative humidity: 95% non-condensing

Warranty: 60 months

Specifications

Dimensions: 375 × 214 × 110 mm

Weight: 12.00 kg (net weight 11.50 kg)

Model: MultiPlus Compact 800VA

Voltage: 230 VAC / 12 V

Housing material: Aluminum

Protection class: IP21

Certifications: ECE R10-4, EN-IEC 60335-1/-2-29, IEC 62109-1, EN 55014-1/-2, IEC 61000-6-1/-6-2/-6-3

Information

35 A battery charger, a powerful pure sine wave inverter, a modern battery charger with adaptive charging technology and a fast 16 A AC switch, all in one compact unit.

PowerAssist feature

Prevents overloading of a limited AC power source. Battery charging is automatically reduced if there is a risk of overload, and the required additional power is drawn from the battery.

Uninterrupted power supply

The NO BREAK feature ensures an automatic switch to battery power in less than 20 ms, maintaining uninterrupted operation of connected devices.

Parallel and Three-Phase Operation

Three units can be configured in a three-phase system. In parallel operation, up to 6 devices or 6 sets of 3 devices each can be connected to achieve higher power output.

Programmable relay.

Defense

Protection against:

• output short circuit
• overload
• battery voltage that is too low or too high

Inverter Specifications

Input: 9.5–17 V
Output: 230 VAC ±2% / 50 Hz ±0.1%
Power at 25 °C:

• 700 W continuous
• 1,600 W maximum

Maximum efficiency: 92%

Standby power consumption: 8 W

Charger Specifications

Suitable for 40–200 Ah batteries

AC input: 187–265 VAC

Charging current:

• Main battery: 35 A
• Starting battery: 4 A

The kit includes a battery temperature sensor and a remote on/off function.

Operating temperature: -40 °C to +65 °C

Maximum relative humidity: 95%, non-condensing

Battery cables: 1.5 m

AC connection: G-ST18i

Warranty: 60 months

Specifications

Dimensions: 546 × 275 × 147 mm

Weight: 21.70 kg (net weight 18.85 kg)

Model: MultiPlus II 230V

Voltage: 230 VAC / 12 V

Protection class: IP22

Certifications: EN-IEC 60335-1/-2-29, EN-IEC 62109-1/-2, EN 55014-1/-2, EN-IEC 61000-3-2/-3-3/-6-1/-6-2/-6-3

Information

MultiPlus II 230V 12/3000/120-32 with ESS (Energy Storage System) — a powerful pure sine wave inverter, a state-of-the-art battery charger with adaptive charging technology, and a fast 32 A AC switch. An external current sensor option (50/100 A) is available. Ideally suited for professional use in marine applications, yachts, vehicles, and off-grid power systems.

Built-in anti-islanding function and a wide range of ESS certifications for various countries. Several system configurations are available.

PowerControl and PowerAssist features

You can set the maximum current for the grid or generator. The device analyzes other AC loads and uses the remaining power to charge the battery, preventing the generator or grid from overloading (PowerControl). PowerAssist automatically reduces the battery charging current in the event of an overload and supplements the required power from the battery.

Support for Solar Energy

AC power is available even in the event of a grid outage. Suitable for off-grid and grid-connected solar power systems. Compatible with solar charge controllers and grid inverters.

Two AC outputs

The main output, which operates continuously, switches in less than 20 ms, ensuring uninterrupted operation of computers and electronic devices. The second output operates only when AC power is available; it is suitable for loads that should not drain the battery, such as water heaters.

Parallel and Three-Phase Operation

Virtually unlimited power expansion is possible. Up to 3 units can be configured in a three-phase system, while up to 6 units or 6 sets of 3 units each can be operated in parallel for higher power.

Configuration and Remote Management

The settings can be changed in a matter of minutes using a computer and the VEConfigure software (MK3-USB interface). A Cerbo GX or other GX device is required for remote control. Data can be stored and monitored on the VRM platform free of charge.

Inverter Specifications

Input: 9.5–17 V
Output: 230 VAC ±2% / 50 Hz ±0.1%
Power at 25 °C: 2400 W continuous / 5500 W maximum
Maximum efficiency: 93%
No-load power consumption: 13/9 W

Charger Specifications

Suitable for lead-acid and lithium-ion batteries
AC input: 187–265 VAC, 45–65 Hz
Maximum charging current: 120 A
Battery temperature sensor
Programmable relay
Fan cooling
Operating temperature: -40 °C to +65 °C
Maximum humidity: 95% non-condensing

Defense

Protection against short circuits, overloads, excessively high or low battery voltage, overheating, low inverter output, and excessive input voltage ripple.

Battery connections: M8
AC connections: screw terminals 13 mm²

Wall mount included.

Warranty: 60 months

Description:
Powerful true sine wave inverter with integrated battery charger, adaptive charging technology and fast-acting AC power switch - all in one compact unit.

Key features:

• Non-interrupting function: the main output connection takes over the load in < 20 ms in case of power supply problems

• 2 AC outputs: second output active only when AC input is available, ideal for loads that should not drain the battery

• PowerAssist technology: prevents overloading of limited AC power by reducing the charge or temporarily adding power from the battery

• Three-phase option: 3-unit configuration for three-phase output possible

• Parallel operation: up to 6 units (or 6 sets of 3) can be operated in parallel to increase total output

Inverter parameters:

• Input: 9.5-17 V

• Output: 230 VAC ±2% / 50 Hz ±0.1%

• Continuous power (@25 °C): 3000 W

• Maximum power (peak): 6000 W

• Efficiency: up to 93 %

• No-load consumption: 20 W

Charger parameters:

• Suitable for: lead-acid and lithium-ion batteries

• Battery capacity: 400-1200 Ah

• Recommended fuse: 400 A

• Recommended cable:

  • 0-5 m: 2 × 50 mm²

  • 5-10 m: 2 × 70 mm²

• AC input: 187-265 VAC

• Charging current (for house battery): 120 A

• Charging current (starter battery): 4 A

• Temperature sensor: included

• Remote on/off: yes

Additional information:

• Protection class: IP21

• Operating temperature: -40 °C to +65 °C

• Maximum humidity (non-condensing): 95%

• Weight: 18 kg

  Technical Specifications - VICTRON ENERGY MultiPlus 3000VA

  • Dimensions: 362 × 258 × 218 mm

  • Weight: 20,90 kg (net: 18,85 kg)

  • Type: MultiPlus 3000VA

  • Voltage: 230 VAC / 12 V

  • Power: 3.00 kW

  • Housing material: Aluminium

  • IP protection: IP21

  • Certificates/Approvals:

    • ECE R10-4

    • EN-IEC 60335-1 / -2-29

    • IEC 62109-1

    • EN 55014-1 / -2

    • EN-IEC 61000-3-2 / -3-3 / -6-1 / -6-2 / -6-3

  This model combines an inverter and a battery charger with high efficiency, durability and compliance with strict European safety and EMC standards.