12V PSU for Hub 2/ReX 2is a power supply unit, connecting theHub 2control panels to 12 volt DC sources. This is an electronic board, replacing the standard 110/230 V power supply unit in the body of the device.
12V PSU for Hub 2/ReX 2 should be installed by a qualified electrician only.
Before installing the power supply, make sure that the device is disconnected from the mains.
When installing the 12V PSU for Hub 2/ReX 2, follow the general electrical safety rules, as well as the requirements of electrical safety regulatory acts. Never disassemble the device while it is under voltage!
Installation process:
Remove the screws and take off the device from the SmartBracket mounting panel, shifting it down with force.
Switch off the device holding the power button for 2 seconds.
Disconnect power and Ethernet cables.
Wait 5 minutes for the capacitors to discharge.
Remove four screws of the back lid and take it off.
Remove the screws attaching the boards to the device body.
Carefully remove both boards, keeping them in the same plane and not disconnecting them. There is a connector between boards: do not break it.
Disconnect the power supply unit (smaller board) from the mainboard.
Connect 12V PSU for Hub 2/ReX 2 to the mainboard using the eight-pin connector between them. Do not warp or bend the antennas while replacing the board: this can cause the device to malfunction.
Please note: the board contacts should be plugged in the bottom row of the connector (closest to the board). When connected correctly, the boards are on the same level.
Reassemble the boards and the device body than tighten the screws.
Check that the battery and its cables are not clamped. When installed properly, the boards stand firmly on all guides and do not stagger. Holding the boards together with the back lid, turn the device over. The SIM card slot, power, and Ethernet sockets should match accurately and fit the corresponding sockets, and the power button should not be stuck. Change the information about input voltage on the device body to avoid incorrect power connections in the future. Use the special bundled sticker with the instruction.
Connect the power (and Ethernet cable) to the appropriate sockets.
Switch on the 12 V power source.
Do not connect the power cable with a voltage that exceeds the acceptable input voltage.
Switch on the device by holding the power button for 2 seconds.
Close and fix the SmartBracket mounting panel.
Switch on the device, wait until loading, and check the external power status in the Ajax app. If there is no power, and you are using a terminal adapter, check the polarity of the connected wires. If there is no power even after reconnecting, please contact the Support Service.
Maintenance
The device does not require technical maintenance.
12V PSU for Hub/Hub Plus/ReXis a power supply unit, connecting the Hub/Hub Plus control panels as well as the ReX radio signal extender to 12 volt DC sources. This is an electronic board, replacing the standard 110/230 V power supply unit in the body of the device.
12V PSU for Hub/Hub Plus/ReX should be installed by a qualified electrician only.
Before installing the power supply, make sure that the device is disconnected from the mains.
When installing the 12V PSU for Hub/Hub Plus/ReX, follow the general electrical safety rules, as well as the requirements of electrical safety regulatory acts. Never disassemble the device while it is under voltage!
Installation process:
Remove the screws and take off the hub or range extender from the SmartBracket mounting panel, shifting the device up.
Switch off the hub or range extender holding the power button for 2 seconds.
Disconnect power and Ethernet cables.
Wait 5 minutes for the capacitors to discharge.
Remove four screws of the back lid and take it off.
Remove the screws attaching the boards to the device body.
Carefully remove both boards, keeping them in the same plane and not disconnecting them. There is a connector between boards: do not break it.
Disconnect the power supply unit (smaller board) from the mainboard.
Connect 12V PSU Hub/Hub Plus/ReX to the mainboard using the eight-pin connector between them. Do not warp or bend the antennas while replacing the board: this can cause the device to malfunction.
Reassemble the boards and the device body than tighten the screws.
Check that the battery and its cables are not clamped. When installed properly, the boards stand firmly on all guides and do not stagger. Holding the boards together with the back lid, turn the device over. The SIM card slot, power, and Ethernet sockets should match accurately and fit the corresponding sockets, and the power button should not be stuck.
Change the information about input voltage on the device body to avoid incorrect power connections in the future. Use the special bundled sticker with the instruction included in the set.
Connect the power (and Ethernet cable) to the appropriate sockets.
Switch on the power source to the hub or range extender.
Do not connect the power cable with a voltage that exceeds the acceptable input voltage 12V PSU for Hub/Hub Plus/ReX.
Switch on the device by holding the power button for 2 seconds.
Close and fix the SmartBracket mounting panel.
Switch on the device, wait until loading, and check the external power status in the Ajax app. If there is no power, and you are using a terminal adapter, check the polarity of the connected wires. If there is no power even after reconnecting, pleasecontact the Ajax Support Service.
Maintenance
The device does not require technical maintenance.
AJAXReläför fjärrstyrning av 12V-utrustning. Fungerar endast med någon av AJAX Hub.
Vid installation och drift av elektrisk utrustning ska du följa de allmänna elsäkerhetsföreskrifterna samt kraven i elsäkerhetsföreskrifterna.
Att ansluta reläet till hubben tar mindre än en minut - skanna bara QR-koden med Ajax-appen. Miniatyrenheten (39×33×18 mm) passar enkelt in i en kopplingsdosa, elpanel eller ställverkshus med DIN-hållare. Och den flexibla externa antennen säkerställer en stabil anslutning.
De många inställningsmöjligheterna och den låga strömförbrukningen gör reläet till ett mångsidigt verktyg för styrning av utrustning. Den torra kontakten är inte galvaniskt ansluten till enhetens strömförsörjning, så den kan användas i både lågspännings- och hushållsnät. Reläet kan enkelt anslutas till en strömförsörjning som är kopplad till ett reservbatteri.
Moderna elektriska grindar och barriärer är utrustade med en fjärrkontroll. Den består av en styrenhet och styrenheter som t.ex. en fjärrkontroll. Styrenheten tar emot kommandon från kontrollerna och aktiverar grindens eller barriärens öppnings-/stängningsmekanism.
För att kunna integreras med Ajax måste styrenheten ha en styringång för anslutning av trådbundna knappar och reläer. Avsaknaden av en sådan ingång förhindrar inte anslutningen, men det komplicerar processen avsevärt - reläet måste anslutas direkt till disken eller styrkortet.
Styrenheten kan också ha en styringång som inte är standard eller speciella styr- och driftlägen, vilket också måste beaktas vid integreringen. Det är möjligt att skicka statusinformation för grindar/spärrar ("stängd" och "öppen") till Ajax-applikationen om styrenheten har en statusutgång.
Ajax 6V Barošanas bloks priekš Hub 2/Hub 2 Plus/ReX 2
SKU: 367304808
€23,51€29,97
Enhetspris
6V PSU (type A) user manual
Updated
6V PSU (type A)is an alternative power supply unit to connect an Ajax hub or range extender to 6 V⎓ sources. This is an electronic board, replacing the standard 110/230 V⎓ power supply unit in the body of the device.
6V PSU (type A) should be installed by a qualified electrician only.
Before installing the power supply, ensure the device is disconnected from the mains.
When installing the 6V PSU for Hub 2/Hub 2 Plus/ReX 2, follow the general electrical safety rules, as well as the requirements of electrical safety regulatory acts. Never disassemble the device while it is under voltage!
Installation process:
Remove the screws and take off the device from the SmartBracket mounting panel, shifting it down with force. If the hub or range extender is installed on a surface, move it upwards.
Switch off the device holding the power button for 2 seconds.
Disconnect power and Ethernet cables.
Wait 5 minutesafter switching off for the capacitors to discharge.
Remove four screws of the back lid and take it off.
Remove the screws attaching the boards to the device body.
Carefully remove both boards, keeping them in the same plane and not disconnecting them. There is a connector between boards: do not break it.
Disconnect the power supply unit (smaller board) from the mainboard.
Connect 6V PSU (type A) to the mainboard using the eight-pin connector between them. Do not warp or bend the antennas while replacing the board: this can cause the device to malfunction.
Please note: the board contacts should be plugged in the bottom row of the connector (closest to the board). When connected correctly, the boards are on the same level.
Reassemble the boards and the device body then tighten the screws.
Check that the battery and its cables are not clamped. When installed properly, the boards stand firmly on all guides and do not stagger. Holding the boards together with the back lid, turn the device over. The SIM card slots, power, and Ethernet sockets should match accurately and fit the corresponding sockets, and the power button should not be stuck.
Check the information about input voltage on the device body to avoid incorrect power connections in the future. Use the special bundled sticker with the instruction.
Connect the power (and Ethernet cable) to the appropriate sockets.
Switch on the 6V⎓ power source.
Do not connect the power cable with a voltage that exceeds the acceptable input voltage.
Switch on the device by holding the power button for 2 seconds.
Install the hub or range extender onthe SmartBracket mounting panel.Fix the device.
Switch on the device, wait until loading, and check the external power status in the Ajax app. If there is no power, and you are using a terminal adapter, check the polarity of thepower cable. If there is no power even after reconnecting, pleasecontact the Support Service.
We recommend using zinc-air alkaline batteries for long-term autonomous operation. Before connecting such a battery, make sure that all the stickers have been removed, and valves capping the air access are open. If possible, leave the battery with access to air for up to 2 hours. This will start a chemical reaction inside and ensure proper functioning.
{"id":55844753211727,"title":"Default Title","option1":"Default Title","option2":null,"option3":null,"sku":"External Antenna black","requires_shipping":true,"taxable":true,"featured_image":null,"available":true,"name":"Ajax antena | LTE vai radio sakariem, SMA savienotājs, vads līdz 3 m, līmējams stiprinājums","public_title":null,"options":["Default Title"],"price":2181,"weight":0,"compare_at_price":2781,"inventory_management":"shopify","barcode":null,"requires_selling_plan":false,"selling_plan_allocations":[],"quantity_rule":{"min":1,"max":null,"increment":1}}
Antena. Koaksiālais kabelis. SMA savienotājs (vīriešu).
Saderīgie hubi
Lai antena darbotos, nepieciešams saderīgs Ajax hub.
Ierīce ir saderīga ar:
Hub BP Jeweller
ExternalAntenna tiek pārdota atsevišķi.
Darbības princips
ExternalAntenna uzlabo sakarus starp hubu un pievienotajām ierīcēm vai mobilo tīklu. Tā ir noderīga, ja hubs tiek uzstādīts seifā, dzelzsbetona telpā vai citās vietās, kur signālam jāpārvar šķēršļi. Antenu var pievienot nepieciešamajiem Jeweller, Wings vai Cellular savienotājiem.
Uzstādīšanas vietas izvēle
Izvēloties antenas uzstādīšanas vietu, jāņem vērā faktori, kas ietekmē tās darbību:
Izvēlētā sakaru kanāla signāla stiprums (Jeweller, Wings vai Cellular).
Attālums starp antenu un hubu. Izmantojot divas vai vairākas antenas, attālumam starp tām jābūt vismaz 60 cm.
Šķēršļi, kas ietekmē radio signālu: sienas, starpstāvu pārsegumi un telpā esoši lieli priekšmeti.
Izstrādājot Ajax sistēmu, ievērojiet uzstādīšanas ieteikumus. Drošības sistēmu drīkst projektēt un uzstādīt tikai speciālisti. Ieteikto Ajax partneru saraksts pieejams šeit.
Vietas, kur antenu nedrīkst uzstādīt
Telpās, kur temperatūra un mitrums pārsniedz pieļaujamos limitus. Tas var sabojāt antenu.
Vietās ar zemu signāla līmeni. Tas var izraisīt savienojuma zudumu.
Tuvu metāla priekšmetiem un spoguļiem. Vadītspējīgi priekšmeti var aizsegt antenu.
Sagatavošanās uzstādīšanai
Pirms ārējās antenas uzstādīšanas pārliecinieties, ka:
hubs ir saderīgs ar ExternalAntenna;
hubam uzstādīšanas vietā ir stabils 2–3 stabiņu signāls ar mobilo tīklu;
uzstādīšanas vietā visām pievienotajām ierīcēm ir stabils 2–3 stabiņu signāls;
kabeļa garums no huba līdz uzstādīšanas vietai ir pietiekams.
Kabeļu izvietojums
Sagatavojot kabeļu maršrutēšanu, pārbaudiet sava reģiona elektroinstalācijas un ugunsdrošības noteikumus. Stingri ievērojiet šos standartus un noteikumus. Praktiski ieteikumi par kabeļu izvietojumu ir pieejami šajā rakstā.
Kabeļu maršrutēšana
Pirms uzstādīšanas rūpīgi izlasiet sadaļu Uzstādīšanas vietas izvēle. Izvairieties no novirzēm no sistēmas projekta. Pamatnoteikumu un šīs rokasgrāmatas ieteikumu neievērošana var radīt ierīces darbības traucējumus. Uzzināt vairāk
Uzstādīšana
Pirms uzstādīšanas pārliecinieties, ka esat izvēlējies optimālo ierīces vietu, kas atbilst šīs rokasgrāmatas prasībām.
Ierīci drīkst uzstādīt tikai profesionāls elektriķis.
Kā uzstādīt ExternalAntenna
Pirms antenas uzstādīšanas izlasiet attiecīgā huba rokasgrāmatu.
Pirms uzstādīšanas pārliecinieties, ka hubs ir atslēgts no strāvas.
Noņemiet huba priekšējo vāku.
Identificējiet Jeweller, Wings vai Cellular savienotājus uz plates.
Noņemiet izolācijas vāciņu no izvēlētā savienotāja.
Pievienojiet antenas SMA (vīriešu) savienotāju pie plates SMA (sieviešu) savienotāja.
Ieslēdziet hubu. Aizveriet huba korpusu. Noņemiet aizsargplēvi no iepriekš uzklātās divpusējās līmlentes. Uzstādiet antenu izvēlētajā vietā. Pārbaudiet savienojuma statusu lietotnē.
Statusi
Huba statusos ir informācija par antenas savienojuma stāvokli. Šie statusi ir pieejami Ajax lietotnē:
Atveriet cilni Ierīces.
Sarakstā izvēlieties hubu.
Ja ExternalAntenna tiek bojāta, sistēma paziņos par to lietotājam un CMS.
Apkope
ExternalAntenna neprasa apkopi.
Tehniskās specifikācijas Visas tehniskās specifikācijas
Atbilstība standartiem
Garantija
Sabiedrības ar ierobežotu atbildību “Ajax Systems Manufacturing” produktu garantija ir derīga 2 gadus pēc iegādes.
Ja ierīce nedarbojas pareizi, vispirms sazinieties ar Ajax tehnisko atbalstu. Vairumā gadījumu tehniskas problēmas var atrisināt attālināti.
Tillgänglig för hämtning på
Slut i lager på
Tillagd för jämförelse
Gräns på count_product-produkt uppnådd
Tillagd för jämförelse
Gräns på count_product-produkt uppnådd
{"id":41592063033527,"title":"Default Title","option1":"Default Title","option2":null,"option3":null,"sku":"367304847","requires_shipping":true,"taxable":true,"featured_image":null,"available":true,"name":"AJAX MotionCam Outdoor Trådlös rörelsedetektor för utomhusbruk med fotoverifiering Vit","public_title":null,"options":["Default Title"],"price":25894,"weight":0,"compare_at_price":33025,"inventory_management":"shopify","barcode":"4820246099196","requires_selling_plan":false,"selling_plan_allocations":[],"quantity_rule":{"min":1,"max":null,"increment":1}}
AJAX MotionCam Outdoor Trådlös rörelsedetektor för utomhusbruk med fotoverifiering Vit
SKU: 367304847
€258,94€330,25
Enhetspris
MotionCam Trådlös rörelsedetektor för utomhusbruk med fotoverifiering.
Fungerar endast med AJAX kontrollpanelHub 2 ellerHub 2 Plus.
Skickar en verifieringsbild till användaren på 9 sekunder.
Med MotionCam Outdoor vet du hur det verkligen står till hemma, till och med innan tjuvarna inser att de har blivit påkomna. En serie animerade foton skickas direkt när rörelse upptäcks.
Lätt att lägga till genom att skanna enhetens QR-kod i Ajax-appen.
Sändningshastighet för fotoverifiering: 9 sekunder
Bildupplösning: 640 x 352 / 320 x 176
Antal bilder i serie: 1 till 5
Nattseende: Infraröd
Installationshöjd: 0,8 till 1,3 m
Strömförsörjning: CR123A (×4), 3 V, upp till 3 år
Ingen garanti på batterier.
Driftstemperatur: -25°C till +60°C
Storlek:206 × 108 × 93 mm
Vikt: 470 g
Installationsanvisningar finns i Ajax-appen, som öppnas när du skannar detektorns QR-kod under installationen. Enkel installation och anslutning till Ajax Hub.
Tillgänglig för hämtning på
Slut i lager på
Tillagd för jämförelse
Gräns på count_product-produkt uppnådd
Tillagd för jämförelse
Gräns på count_product-produkt uppnådd
{"id":46866019025231,"title":"Default Title","option1":"Default Title","option2":null,"option3":null,"sku":"367308965","requires_shipping":true,"taxable":true,"featured_image":null,"available":true,"name":"AJAX MotionCam Outdoor PhOD (Picture on Demand) trådlös rörelsedetektor för utomhusbruk med fotoverifiering i vitt","public_title":null,"options":["Default Title"],"price":28485,"weight":0,"compare_at_price":36330,"inventory_management":"shopify","barcode":"4823114014284","requires_selling_plan":false,"selling_plan_allocations":[],"quantity_rule":{"min":1,"max":null,"increment":1}}
AJAX MotionCam Outdoor PhOD (Picture on Demand) trådlös rörelsedetektor för utomhusbruk med fotoverifiering i vitt
SKU: 367308965
€284,85€363,30
Enhetspris
MotionCam Outdoor PhOD trådlös rörelsedetektor med fotoverifiering.
PhOD (Photo on Demand) - Picture on Demand - ta en bild när som helst och få reda på vad som händer på din egendom.
Fungerar endast med AJAX Hub2Hub 2 ellerHub 2 Plus.
Skickar en verifieringsbild till användaren på 9 sekunder.
Med MotionCam Outdoor får du reda på den verkliga situationen hemma redan innan inbrottstjuvarna inser att de har fångats. En serie animerade foton skickas direkt när rörelse detekteras.
Lätt att lägga till genom att skanna enhetens QR-kod i Ajax-appen.
Sändningshastighet för fotoverifiering: 9 sekunder
Bildupplösning: 640 x 352 / 320 x 176
Antal bilder i serie: 1 till 5
Nattseende: Infraröd
Installationshöjd: 0,8 till 1,3 m
Strömförsörjning: CR123A (×4), 3 V, upp till 3 år
Ingen garanti på batterier.
Driftstemperatur: -25°C till +60°C
Storlek:206 × 108 × 93 mm
Vikt: 470 g
Installationsanvisningar finns i Ajax-appen, som öppnas när du skannar detektorns QR-kod under installationen. Enkel installation och anslutning till Ajax Hub.
Tillgänglig för hämtning på
Slut i lager på
Tillagd för jämförelse
Gräns på count_product-produkt uppnådd
Tillagd för jämförelse
Gräns på count_product-produkt uppnådd
{"id":41592063721655,"title":"Default Title","option1":"Default Title","option2":null,"option3":null,"sku":"367308694","requires_shipping":true,"taxable":true,"featured_image":null,"available":true,"name":"AJAX Trådlös siren för utomhusbruk StreetSiren, vit","public_title":null,"options":["Default Title"],"price":12799,"weight":0,"compare_at_price":14997,"inventory_management":"shopify","barcode":"856963007156","requires_selling_plan":false,"selling_plan_allocations":[],"quantity_rule":{"min":1,"max":null,"increment":1}}
AJAX Trådlös siren för utomhusbruk StreetSiren, vit
SKU: 367308694
€127,99€149,97
Enhetspris
Ajax trådlös utomhussirenStreetSiren, som avger ett larm när detektorn aktiveras. Den är lämplig för utomhusområden för att varna för fara eller avskräcka inkräktare. Sirenen fungerar endast tillsammans med en av Ajax kontrollpaneler.
Siren med LED-ram. IP54-skydd np -25°C till +50°C. Fungerar i upp till 5 år.
Volym: Justerbar, 85-113 dB inom 1 m
Larmlängd: Justerbar, 3-180 s
Indikering av till-/frånkoppling: Ja
Larmets överföringstid: 0,15 s
Strömförsörjning: 4x CR123A-batterier, 3 V
Batteriets livslängd: 5 år
Ingen garanti på batterier
Kommunikationsräckvidd: 2000 m i öppen miljö
Driftstemperatur: -25°C till +50°C
Skyddsklass: IP54
Storlek: 200 × 200 × 51 mm
Vikt: 528 g
Installationsanvisningar finns i Ajax-appen, som öppnas när detektorns QR-kod skannas under installationen. Enkel installation och anslutning till Ajax Hub.
Tillgänglig för hämtning på
Slut i lager på
Tillagd för jämförelse
Gräns på count_product-produkt uppnådd
Tillagd för jämförelse
Gräns på count_product-produkt uppnådd
{"id":41613546062007,"title":"Default Title","option1":"Default Title","option2":null,"option3":null,"sku":"367304816","requires_shipping":true,"taxable":true,"featured_image":null,"available":true,"name":"AJAX DoorProtect Trådlös kontakt för säkerhetsdörr i vitt","public_title":null,"options":["Default Title"],"price":3528,"weight":0,"compare_at_price":4499,"inventory_management":"shopify","barcode":null,"requires_selling_plan":false,"selling_plan_allocations":[],"quantity_rule":{"min":1,"max":null,"increment":1}}
AJAX DoorProtect Trådlös kontakt för säkerhetsdörr i vitt
SKU: 367304816
(2)
€35,28€44,99
Enhetspris
DoorProtect trådlös dörrkontakt som ansluts till ditt AJAX säkerhetssystem.
En inbrottsdetektor som meddelar dig när en dörr eller ett fönster är öppet. Lämplig för alla typer av dörrar. Larmaviseringar vid obehöriga borttagningsförsök.
Batteritid 7 år.
Består av 2 delar - öppningsdetektor och magnet.
Drifttemperatur: -10°C till +40°C
Mått: Diameter: 20 mm, Höjd: 90 mm
Vikt: 29 g
Ingen garanti för batterier
Installationsanvisningar finns i Ajax-appen, som öppnas när QR-koden på detektorn skannas under installationen. Enkel installation och anslutning till Ajax Hub
Tillgänglig för hämtning på
Slut i lager på
Tillagd för jämförelse
Gräns på count_product-produkt uppnådd
Tillagd för jämförelse
Gräns på count_product-produkt uppnådd
{"id":41613546029239,"title":"Default Title","option1":"Default Title","option2":null,"option3":null,"sku":"367304813","requires_shipping":true,"taxable":true,"featured_image":null,"available":true,"name":"AJAX DoorProtect Trådlös kontakt för säkerhetsdörr Svart","public_title":null,"options":["Default Title"],"price":3528,"weight":0,"compare_at_price":4499,"inventory_management":"shopify","barcode":"856963007040","requires_selling_plan":false,"selling_plan_allocations":[],"quantity_rule":{"min":1,"max":null,"increment":1}}
AJAX DoorProtect Trådlös kontakt för säkerhetsdörr Svart
SKU: 367304813
€35,28€44,99
Enhetspris
DoorProtect trådlös dörrkontakt som ansluts till ditt AJAX säkerhetssystem.
En inbrottsdetektor som meddelar dig när en dörr eller ett fönster är öppet. Lämplig för alla typer av dörrar. Larmaviseringar vid obehöriga borttagningsförsök.
Batteritid 7 år.
Består av 2 delar - öppningsdetektor och magnet.
Drifttemperatur: -10°C till +40°C
Mått: Diameter: 20 mm, Höjd: 90 mm
Vikt: 29 g
Ingen garanti för batterier
Installationsanvisningar finns i Ajax-appen, som öppnas när QR-koden på detektorn skannas under installationen. Enkel installation och anslutning till Ajax Hub
Tillgänglig för hämtning på
Slut i lager på
Tillagd för jämförelse
Gräns på count_product-produkt uppnådd
Tillagd för jämförelse
Gräns på count_product-produkt uppnådd
{"id":41592070176951,"title":"Default Title","option1":"Default Title","option2":null,"option3":null,"sku":"367304815","requires_shipping":true,"taxable":true,"featured_image":null,"available":true,"name":"AJAX DoorProtect Plus trådlös säkerhetsdörrkontakt med stöt- och förflyttningssensor. Vit","public_title":null,"options":["Default Title"],"price":5293,"weight":0,"compare_at_price":6749,"inventory_management":"shopify","barcode":"856963007941","requires_selling_plan":false,"selling_plan_allocations":[],"quantity_rule":{"min":1,"max":null,"increment":1}}
AJAX DoorProtect Plus trådlös säkerhetsdörrkontakt med stöt- och förflyttningssensor. Vit
SKU: 367304815
€52,93€67,49
Enhetspris
DoorProtect Plus trådlös dörrkontakt som ansluts till ditt AJAX säkerhetssystem.
En inbrottsdetektor som meddelar dig när en dörr eller ett fönster är öppet. Lämplig för alla typer av dörrar. Larmaviseringar vid obehöriga borttagningsförsök. Reagerar även på stötar, vibrationer och platsförändringar.
Batteritid 7 år.
Består av 2 delar - öppningsdetektor och magnet.
Drifttemperatur: -10°C till +40°C
Mått: Diameter: 20 mm, Höjd: 90 mm
Vikt: 29 g
Ingen garanti för batterier
Installationsanvisningar finns i Ajax-appen, som öppnas när QR-koden på detektorn skannas under installationen. Enkel installation och anslutning till Ajax Hub
Tillgänglig för hämtning på
Slut i lager på
Tillagd för jämförelse
Gräns på count_product-produkt uppnådd
Tillagd för jämförelse
Gräns på count_product-produkt uppnådd
{"id":41592069947575,"title":"Default Title","option1":"Default Title","option2":null,"option3":null,"sku":"367304814","requires_shipping":true,"taxable":true,"featured_image":null,"available":true,"name":"AJAX DoorProtect Plus trådlös säkerhetsdörrkontakt med stöt- och förflyttningssensor. Svart","public_title":null,"options":["Default Title"],"price":6749,"weight":0,"compare_at_price":6749,"inventory_management":"shopify","barcode":"856963007958","requires_selling_plan":false,"selling_plan_allocations":[],"quantity_rule":{"min":1,"max":null,"increment":1}}
AJAX DoorProtect Plus trådlös säkerhetsdörrkontakt med stöt- och förflyttningssensor. Svart
SKU: 367304814
€67,49
Enhetspris
DoorProtect Plus trådlös dörrkontakt som ansluts till ditt AJAX säkerhetssystem.
En inbrottsdetektor som meddelar dig när en dörr eller ett fönster är öppet. Lämplig för alla typer av dörrar. Larmaviseringar vid obehöriga borttagningsförsök. Reagerar även på stötar, vibrationer och platsförändringar.
Batteritid 7 år.
Består av 2 delar - öppningsdetektor och magnet.
Drifttemperatur: -10°C till +40°C
Mått: Diameter: 20 mm, Höjd: 90 mm
Vikt: 29 g
Ingen garanti för batterier
Installationsanvisningar finns i Ajax-appen, som öppnas när QR-koden på detektorn skannas under installationen. Enkel installation och anslutning till Ajax Hub
Tillgänglig för hämtning på
Slut i lager på
Tillagd för jämförelse
Gräns på count_product-produkt uppnådd
Tillagd för jämförelse
Gräns på count_product-produkt uppnådd
{"id":41592060346551,"title":"Default Title","option1":"Default Title","option2":null,"option3":null,"sku":"367304833","requires_shipping":true,"taxable":true,"featured_image":null,"available":true,"name":"AJAX Trådlös siren för inomhusbruk HomeSiren Vit","public_title":null,"options":["Default Title"],"price":7496,"weight":0,"compare_at_price":7496,"inventory_management":"shopify","barcode":"856963007286","requires_selling_plan":false,"selling_plan_allocations":[],"quantity_rule":{"min":1,"max":null,"increment":1}}
Ajax trådlös inomhus sirenHomeSiren, som avger ett larm när detektorn aktiveras. Den är lämplig för inomhusbruk för att varna för fara eller avskräcka inkräktare. Sirenen fungerar endast tillsammans med en av Ajax kontrollpaneler.
Indikator för säkerhetsläge, justerbar larmljudnivå och varaktighet för detektorns aktiveringstid.
Installationsprincip:
Anslutning till kontrollpanelen med ett klick.
Typ av siren: Trådlös
Installation: Inomhus
Kompatibilitet: med alla Ajax säkerhetspaneler
Typ av meddelande: Ljudande siren
Volym: Justerbar, 81-105 dB inom 1 m
Larmlängd: Justerbar, 3-180 s
Indikering av till-/frånkoppling: Ja
Larmets överföringstid: 0,15 s
Strömförsörjning: Två CR123A-batterier, 3 V
Batteriets livslängd: 5 år
Ingen garanti på batterier
Kommunikationsräckvidd - 2000 m i öppen miljö
Drifttemperatur: -10°C till +40°C
Skyddsklass: IP50
Storlek: 75 × 76 × 27 mm
Vikt: 97 g
Installationsanvisningar finns i Ajax-appen, som öppnas när du skannar detektorns QR-kod under installationen. Enkel installation och anslutning till Ajax Hub.
Tillgänglig för hämtning på
Slut i lager på
Tillagd för jämförelse
Gräns på count_product-produkt uppnådd
Tillagd för jämförelse
Gräns på count_product-produkt uppnådd
{"id":41592060575927,"title":"Default Title","option1":"Default Title","option2":null,"option3":null,"sku":"367304832","requires_shipping":true,"taxable":true,"featured_image":null,"available":true,"name":"AJAX Trådlös siren för inomhusbruk HomeSiren Svart","public_title":null,"options":["Default Title"],"price":5877,"weight":0,"compare_at_price":7496,"inventory_management":"shopify","barcode":"856963007293","requires_selling_plan":false,"selling_plan_allocations":[],"quantity_rule":{"min":1,"max":null,"increment":1}}
AJAX Trådlös siren för inomhusbruk HomeSiren Svart
SKU: 367304832
€58,77€74,96
Enhetspris
Ajax trådlös inomhus sirenHomeSiren, som avger ett larm när detektorn aktiveras. Den är lämplig för inomhusbruk för att varna för fara eller avskräcka inkräktare. Sirenen fungerar endast tillsammans med en av Ajax kontrollpaneler.
Indikator för säkerhetsläge, justerbar larmljudnivå och varaktighet för detektorns aktiveringstid.
Installationsprincip:
Anslutning till kontrollpanelen med ett klick.
Typ av siren: Trådlös
Installation: Inomhus
Kompatibilitet: med alla Ajax säkerhetspaneler
Typ av meddelande: Ljudande siren
Volym: Justerbar, 81-105 dB inom 1 m
Larmlängd: Justerbar, 3-180 s
Indikering av till-/frånkoppling: Ja
Larmets överföringstid: 0,15 s
Strömförsörjning: Två CR123A-batterier, 3 V
Batteriets livslängd: 5 år
Ingen garanti på batterier
Kommunikationsräckvidd - 2000 m i öppen miljö
Drifttemperatur: -10°C till +40°C
Skyddsklass: IP50
Storlek: 75 × 76 × 27 mm
Vikt: 97 g
Installationsanvisningar finns i Ajax-appen, som öppnas när du skannar detektorns QR-kod under installationen. Enkel installation och anslutning till Ajax Hub.
Tillgänglig för hämtning på
Slut i lager på
Tillagd för jämförelse
Gräns på count_product-produkt uppnådd
Tillagd för jämförelse
Gräns på count_product-produkt uppnådd
{"id":41592068341943,"title":"Default Title","option1":"Default Title","option2":null,"option3":null,"sku":"367304853","requires_shipping":true,"taxable":true,"featured_image":null,"available":true,"name":"AJAX MotionProtect trådlös säkerhetsrörelsedetektor i vitt","public_title":null,"options":["Default Title"],"price":6399,"weight":0,"compare_at_price":7496,"inventory_management":"shopify","barcode":"856963007200","requires_selling_plan":false,"selling_plan_allocations":[],"quantity_rule":{"min":1,"max":null,"increment":1}}
AJAX MotionProtect trådlös säkerhetsrörelsedetektor i vitt
SKU: 367304853
€63,99€74,96
Enhetspris
MotionProtect trådlös rörelsedetektor som kan anslutas till en Ajax säkerhetspanel. Meddelar användaren om ett intrång i fastigheten. Detektorn bör monteras på väggen mittemot dörren eller på någon annan plats där den kan brytas upp. Sabotagelarm - du får ett meddelande om någon försöker ta bort detektorn. Batteritid 5 år.
Detektorn reagerar inte på djur upp till 20 kg och 50 cm. Passiv infraröd detekteringsalgoritm för att minska falsklarm. Detektorn justerar känslighetsnivån beroende på omgivningstemperaturen för att fungera effektivt i kallt och varmt väder.
Klar att använda direkt ur lådan - batteriet sitter i, montera det bara på fästet som medföljer detektorn.
Driftstemperatur: -10°C till +40°C
Storlek: 110 × 65 × 50 mm
Vikt: 96 g
Ingen garanti för batterier.
Installationsanvisningar finns i Ajax-appen, som öppnas när detektorns QR-kod skannas under installationen. Enkel installation och anslutning till Ajax Hub.
MotionProtect trådlös rörelsedetektor som kan anslutas till en Ajax säkerhetspanel. Meddelar användaren om ett intrång i fastigheten. Detektorn bör monteras på väggen mittemot dörren eller på någon annan plats där den kan brytas upp. Sabotagelarm - du får ett meddelande om någon försöker ta bort detektorn. Batteritid 5 år.
Detektorn reagerar inte på djur upp till 20 kg och 50 cm. Passiv infraröd detekteringsalgoritm för att minska falsklarm. Detektorn justerar känslighetsnivån beroende på omgivningstemperaturen för att fungera effektivt i kallt och varmt väder.
Klar att använda direkt ur lådan - batteriet sitter i, montera det bara på fästet som medföljer detektorn.
Driftstemperatur: -10°C till +40°C
Storlek: 110 × 65 × 50 mm
Vikt: 96 g
Ingen garanti för batterier.
Installationsanvisningar finns i Ajax-appen, som öppnas när detektorns QR-kod skannas under installationen. Enkel installation och anslutning till Ajax Hub.
Tillgänglig för hämtning på
Slut i lager på
Tillagd för jämförelse
Gräns på count_product-produkt uppnådd
Tillagd för jämförelse
Gräns på count_product-produkt uppnådd
{"id":46870133211471,"title":"Default Title","option1":"Default Title","option2":null,"option3":null,"sku":"367304862","requires_shipping":true,"taxable":true,"featured_image":null,"available":true,"name":"AJAX trådlöst säkerhetssystem fjärrkontroll SpaceControl i vitt","public_title":null,"options":["Default Title"],"price":2940,"weight":0,"compare_at_price":3749,"inventory_management":"shopify","barcode":null,"requires_selling_plan":false,"selling_plan_allocations":[],"quantity_rule":{"min":1,"max":null,"increment":1}}
AJAX trådlöst säkerhetssystem fjärrkontroll SpaceControl i vitt
SKU: 367304862
€29,40€37,49
Enhetspris
Trådlös fjärrkontroll SpaceControl med larmknapp. AnvändSpaceControl för att aktivera och avaktivera säkerhetssystemet, aktivera nattläget och sända ett larm.
Alla säkerhetssystem kan styras via Ajax-appen på din smartphone, men om du har en smart telefon kan du använda SpaceControl-fjärrkontrollen .
Omedelbart redo att användas: batteriet sitter i fjärrkontrollen. Lägg helt enkelt till enheten i ditt säkerhetssystem genom att skanna QR-koden i Ajax-appen.
5 års batteritid.
Driftstemperatur: -25°C till +50°C
Storlek: 65 × 37 × 10 mm
Vikt: 13 g
Ingen garanti på batterier.
Installationsanvisningar finns i Ajax-appen, som öppnas när detektorns QR-kod skannas under installationen. Enkel installation och anslutning till Ajax Hub.
Trådlös fjärrkontroll SpaceControl med larmknapp. AnvändSpaceControl för att aktivera och avaktivera säkerhetssystemet, aktivera nattläget och sända ett larm.
Alla säkerhetssystem kan styras via Ajax-appen på din smartphone, men om du har en smart telefon kan du använda SpaceControl-fjärrkontrollen .
Omedelbart redo att användas: batteriet sitter i fjärrkontrollen. Lägg helt enkelt till enheten i ditt säkerhetssystem genom att skanna QR-koden i Ajax-appen.
5 års batteritid.
Driftstemperatur: -25°C till +50°C
Storlek: 65 × 37 × 10 mm
Vikt: 13 g
Ingen garanti på batterier.
Installationsanvisningar finns i Ajax-appen, som öppnas när detektorns QR-kod skannas under installationen. Enkel installation och anslutning till Ajax Hub.
Tillgänglig för hämtning på
Slut i lager på
Tillagd för jämförelse
Gräns på count_product-produkt uppnådd
Tillagd för jämförelse
Gräns på count_product-produkt uppnådd
{"id":41613546651831,"title":"Default Title","option1":"Default Title","option2":null,"option3":null,"sku":"367308948","requires_shipping":true,"taxable":true,"featured_image":null,"available":true,"name":"AJAX trådlös säkerhetsknappsats Plus vit","public_title":null,"options":["Default Title"],"price":11760,"weight":0,"compare_at_price":14997,"inventory_management":"shopify","barcode":"367304848","requires_selling_plan":false,"selling_plan_allocations":[],"quantity_rule":{"min":1,"max":null,"increment":1}}
AJAX Keypad Plus trådlöst tangentbord, ansluts till AJAX Hub 2 eller Hub 2 Plus. Slå på och av säkerhet, nattläge med knappsatsen.
Batteritid upp till 3,5 år. Skapa en personlig kod för varje användare så att du vet vem som har slagit på eller av säkerheten och när. Användarens namn kommer att återspeglas i meddelandeloggen.
Efter 3 misslyckade försök att ange koden skickas ett larm. En larmkod kan skapas för att simulera att en säkerhetsvakt tas bort om någon tvingar användaren att ta bort säkerhetsvakten, men larmet skickas omedelbart till säkerhetsföretaget.
Tillgänglig för hämtning på
Slut i lager på
Tillagd för jämförelse
Gräns på count_product-produkt uppnådd
Tillagd för jämförelse
Gräns på count_product-produkt uppnådd
{"id":41613546619063,"title":"Default Title","option1":"Default Title","option2":null,"option3":null,"sku":"367305098","requires_shipping":true,"taxable":true,"featured_image":null,"available":true,"name":"AJAX Wireless Security Keypad Plus Svart","public_title":null,"options":["Default Title"],"price":14997,"weight":0,"compare_at_price":14997,"inventory_management":"shopify","barcode":null,"requires_selling_plan":false,"selling_plan_allocations":[],"quantity_rule":{"min":1,"max":null,"increment":1}}
AJAX Keypad Plus bezvadu tastatūra, pieslēdzama pie AJAX Hub 2 vai Hub 2 Plus. Ieslēdziet un izslēdziet apsardzi, nakts režīmu ar tastatūras palīdzību.
Baterijas strādā līdz 3.5 gadiem. Izveidojiet katram lietotājiem personīgu kodu, lai zinātu, kurš un kad ieslēdzis vai izlēdzis apsardzi. Lietotāja vārds tiks atspoguļots paziņojumu žurnālā.
Pēc 3 neveiksmīgiem koda ievadīšanas mēģinājumiem tiks nosūtīts trauksmes signāls. Var izveidot trauksmes kodu, ievadot kuru, tiek simulēta apsardzes noņēmšana, ja kāds piespiež lietotāju noņemt apsardzi, taču trauksmes signāls tiek nekavējoties sūtīts apsardzes kompānijai.
KeyPad Plus Jeweller user manual
Updated
KeyPad Plus Jewelleris a wireless touch keypad for managing the Ajax system with encrypted contactless cards and key fobs. Designed for indoor installation. Supports “silent alarm” when entering theduress code.
The keypad manages security modes using passwords andcardsorkey fobs. Indicates the current security mode with a LED light.
The keypad operates as part of the Ajax system by connecting via theJeweller secure radio communication protocolto the hub. The communication range without obstacles is up to 1700 meters. The pre-installed battery life is up to 3.5 years.
SmartBracket mounting plate (to remove the plate, slide it down)
Do not tear off the perforated part of the mount. It is required for actuating the tamper in case of any attempt to dismantle the keypad.
Power button
Tamper button
Keypad QR Code
Operating principle
KeyPad Plus Jeweller arms and disarms the security of the entire facility or separate groups as well as allows activating theNight Mode. You can control the security modes with KeyPad Plus Jeweller using:
Codes. The keypad supports general and personal codes, as well as arming without entering a code.
Cards or key fobs. You can connectTag key fobsandPass cardsto the system. To quickly and securely identify users, KeyPad Plus Jeweller uses the DESFire® technology. DESFire® is based on the ISO 14443 international standard and combines 128-bit encryption and copy protection.
KeyPad Plus Jeweller supports code types as follows:
Keypad code— general code set up for the keypad. When used, all events are delivered to Ajax apps on behalf of the keypad.
User code— personal code set up for a user connected to the hub. When used, all events are delivered to Ajax apps on behalf of the user.
Keypad access code— set up for a person who is not registered in the system. When used, events are delivered to Ajax apps with a name associated with this code.
RRU codeis an access code for the rapid response units (RRU) activated after the alarm and valid for a specified period. When the code is activated and used, events are delivered to Ajax apps with a title associated with this code.
The number of personal, access, and RRU codes depends on the hub model.
Access codes are not supported by theHub (2G) Jewellercontrol panel.
Before entering a code or using Tag/Pass, you should activate (“wake up”) the KeyPad Plus Jeweller by sliding your hand over the touch panel from top to bottom. When it is activated, the button backlight is enabled, and the keypad beeps.
Auto-wake on Delay when Enteringfunction allows automatically activating the keypad whenDelay When Enteringis set up. This function is supported by KeyPad Plus Jeweller with firmware version 6.60.0.6 or higher and hubs withOS Malevich 2.19or higher.
The KeyPad Plus Jeweller is equipped with LED indicators that show the current security mode and keypad malfunctions (if any). The security status is displayed only when the keypad is active (the device backlight is on).
You can use the KeyPad Plus Jeweller without ambient lighting as the keypad has a backlight. The pressing of the buttons is accompanied by a sound signal. The backlight brightness and keypad volume are adjustable in the settings. If you do not touch the keypad for 4 seconds, KeyPad Plus Jeweller reduces the backlight brightness, and 8 seconds later goes into power-saving mode and turns off the display.
If the batteries are discharged, the backlight turns on at the minimum level regardless of the settings.
Function button
KeyPad Plus Jeweller has aFunctionbutton that operates in 3 modes:
Off— the button is disabled and nothing happens after it is pressed.
Alarm— after theFunctionbutton is pressed, the system sends an alarm to the security company monitoring station and all users.
Mute interconnected fire detectors alarm— after theFunctionbutton is pressed, the system mutes the alarm of theAjax fire detectors. Available only if anInterconnected Fire Detectors Alarmis enabled (Hub → Settings→ Service → Fire detectors settings)
KeyPad Plus Jeweller supportsduress code. It allows you to simulate alarm deactivation. TheAjax appandsirensinstalled at the facility will not give you away in this case, but the security company and other users of the security system will be warned about the incident.
KeyPad Plus Jeweller can participate in two-stage arming, but cannot be used as a second-stage device. The two-stage arming process using Tag or Pass is similar to arming using a personal or general code on the keypad.
The Ajax system can connect to the CMS and transmit events and alarms to the monitoring station of the security company inSurGard (Contact ID), ADEMCO 685, SIA (DC-09), and other proprietary protocol formats. A complete list of supported protocols isavailable here. The device ID and the number of the loop (zone) can be found inits states.
Connection
KeyPad Plus Jeweller is incompatible with Hub (2G) Jeweller, third-party security central units, and ocBridge Plus and uartBridge integration modules.
Before starting connection
The hub and the device operating at different radio frequencies are incompatible. The radio-frequency range of the device may vary by region. We recommend purchasing and using Ajax devices in the same region. You can check the range of operating radio frequencies with thetechnical support service.
Install the Ajax app andcreate an account. Add a hub and create at least one room.
Ensure that the hub is on and has Internet access (via Ethernet cable, Wi-Fi, and/or mobile network). This can be done by opening the Ajax app or by looking at the hub logo on the faceplate — it lights white or green if the hub is connected to the network.
Make sure that the hub is not in armed mode and does not start updates by checking its status in the app.
Only a user or PRO with full admin rights can add a device to the hub.
To connect KeyPad Plus Jeweller
Open the Ajax app. If your account has access to multiple hubs, select the one to which you want to connect KeyPad Plus Jeweller.
Go to theDevicesmenu and clickAdd Device.
Name the keypad, scan or enter the QR code (located on the package and under the SmartBracket mount), and select a room.
ClickAdd; the countdown will begin.
Turn on the keypad by holding the power button for 3 seconds. Once connected, KeyPad Plus Jeweller will appear in the hub device list in the app. To connect, locate the keypad at the same protected facility as the system (within the coverage area of the hub radio network range). If the connection fails, try again in 10 seconds.
The keypad only works with one hub. When connected to a new hub, the device stops sending commands to the old hub. Once added to a new hub, KeyPad Plus Jeweller is not removed from the device list of the old hub. This must be done manually through the Ajax app.
KeyPad Plus Jeweller turns off automatically 6 seconds after being turned on if the keypad fails to connect to the hub. Therefore, you do not need to turn off the device to retry the connection.
Updating the statuses of devices in the list depends on the Jeweller settings; the default value is 36 seconds.
Icons
The icons represent some of KeyPad Plus Jeweller states. You can see them in theDevicestab in the Ajax app.
Icon
Value
Jeweller signal strength — Displays the signal strength between the hub or radio signal range extender and KeyPad Plus Jeweller
Displays the status of the ReX Jeweller range extender use.
The field is not displayed if the keypad works directly with the hub.
Pass/Tag Reading
Displays if card and keyfob reader is enabled.
Assigned Group Easy Management
Displays whether or not the security mode can be switched with Pass or Tag and without confirmation by the control buttons,,.
Easy Armed Mode Change
This setting replacesAssigned Group Easy Managementon KeyPad Plus Jeweller with firmware version 5.60.6.3 or higher, operating with hubs withOS Malevich 2.19or higher.
Shows the configuration for theEasy Armed Mode Changefeature:
Off— each arming or disarming attempt should be confirmed by entering the passcode or presenting the access device.
Arm/disarm using access device without confirming action by buttons— allows users to switch security modes of the system using access devices without confirmation by pressing keypad buttons.
Disarm without disarming button— the system or its groups, the security of which is managed with a passcode or access devices, will be disarmed without confirmation by pressing keypad buttons.
A fixed passcode length should be set in the hub settings in the Ajax PRO app.
Permanent Deactivation
Shows the status of the device:
No— the device operates normally and transmits all events.
Lid only— the hub admin has disabled notifications about the body opening.
Entirely— the hub admin has entirely excluded the keypad from the system. The device does not execute system commands and does not report alarms or other events.
Shows the status of the keypad one-time deactivation setting:
No— the keypad operates in normal mode.
Lid only— notifications on the keypad tamper triggering are disabled until the first disarm.
Entirely— the keypad is entirely excluded from the operation of the system until the first disarm. The device does not execute system commands and does not report alarms or other events.
KeyPad Plus Jeweller is configured in the Ajax app:
Go to theDevicestab.
SelectKeyPad Plus Jewellerfrom the list.
Go toSettingsby clicking on the gear icon.
To apply the settings after the change, click theBackbutton
Parameter
Value
Name
Device name. Displayed in the list of hub devices, SMS text, and notifications in the event feed.
To change the device name, click on the pencil icon.
The name can contain up to 12 Cyrillic characters or up to 24 Latin characters.
Room
Selecting the virtual room to which KeyPad Plus Jeweller is assigned.
The name of the room is displayed in the text of SMS and notifications in the event feed.
Group Management
Selecting the security group controlled by the device. You can select all groups or just one.
The field is displayed when theGroup modeis enabled.
If theFollowed groupfeature is configured for groups, their security state can automatically change depending on their settings and initiators’ states.
.
Access Settings
Selecting the method of arming/disarming:
Keypad codes only.
User codes only.
Keypad and user codes.
To activate theKeypad Access Codesset up for people who are not registered in the system, select the options on the keypad:Keypad codes onlyorKeypad and user codes
.
Keypad Code
Selection of a general code for security control. Contains 4 to 6 digits.
Duress Code
Selecting a general duress code for silent alarm. Contains 4 to 6 digits.
Selecting the function of the * button (Functionbutton):
Off— theFunctionbutton is disabled and does not execute any commands when pressed.
Panic— after theFunctionbutton is pressed, the system sends an alarm to the CMS and to all users.
Mute Interconnected Fire Detectors Alarm — when pressed, mutes the alarm ofAjax fire detectors. Available only if anInterconnected Fire Detectors Alarmis enabled.
When enabled, theFunctionbutton should be pressed twice to send a panic alarm.
This setting is available ifFunction buttonis set toPanic.
Unauthorized Access Auto-Lock
If active, the keypad is locked for the pre-set time if an incorrect code is entered or unverified passes/tags are used more than 3 times in a row within 1 minute.
It is not possible to disarm the system via keypad during this time. You can unlock the keypad through the Ajax app.
Auto-lock Time, min
Selecting the keypad lock period after wrong code attempts:
3 minutes.
5 minutes.
10 minutes.
20 minutes.
30 minutes.
60 minutes.
90 minutes.
180 minutes.
Brightness
Selecting brightness of the keypad buttons backlight. The backlight works only when the keypad is active.
This option does not affect the brightness level of pass/tag reader and security modes indicators.
Buttons Volume
Selecting the keypad buttons volume level when pressed.
Pass/Tag Reading
When enabled, the security mode can be controlled with Pass and Tag access devices.
Authorization confirmation with a passcode
When enabled, system authorization using access devices requires confirmation of the action with the user or keypad code. Available if thePass/Tag Readingtoggle is enabled.
This setting is supported when KeyPad Plus Jeweller is connected to hubs with firmware versionOS Malevich 2.20or higher.
Time for confirmation
Selecting the maximum time to confirm authorization with a password after access devices’ confirmation. Available if theAuthorization confirmation with a passcodetoggle is enabled.
This setting is supported when KeyPad Plus Jeweller is connected to hubs with firmware versionOS Malevich 2.21or higher.
Assigned Group Easy Management
When enabled, changing the security mode with Tag and Pass does not require confirmation by pressing thearm,disarm, orNight Modebutton. The security mode is switched automatically.The option is available ifPass/Tag Readingis enabled in the keypad settings.
If the group mode is activated, the option is available when the keypad is assigned to a particular group — theGroup Management field in the keypad settings.
This setting replacesAssigned Group Easy Managementon KeyPad Plus Jeweller with firmware version 5.60.6.3 or higher, operating with hubs withOS Malevich 2.19or higher.
Allows users to arm/disarm the system without confirmation by pressing keypad buttons.
Three options are available:
Off— each arming or disarming attempt should be confirmed by entering the passcode or presenting the access device.
Arm/disarm using access device without confirming action by buttons— allows users to switch security modes of the system using access devices without confirmation with keypad buttons.
Disarm without disarming button— the system or its groups, the security of which is managed with a passcode or access devices, will be disarmed without confirmation by pressing keypad buttons.
A fixed passcode length should be set in the hub settings in the Ajax PRO app.
Arming without Code
The option allows you to arm the system without entering a code. To do so, just click on theArmorNight Modebutton.
Auto-wake on Delay when Entering
The feature is available on KeyPad Plus Jeweller with firmware version 6.60.0.6 or higher, operating with hubs withOS Malevich 2.19or higher.
Activates the keypad afterDelay When Enteringis started by any security device.
The auto-wake feature may also reduce the keypad battery life.
Alert with a siren if the panic button is pressed
The field is displayed if theAlarmoption is selected for theFunctionbutton.When the option is enabled, the sirens connected to the security system give an alert when the * button (Functionbutton) is pressed.
Jeweller Signal Strength Test
Switches the keypad to the Jeweller signal strength test mode.
Opens KeyPad Plus Jeweller user manual in the Ajax app.
Permanent Deactivation
Allows the user to disable the device without removing it from the system.
Three options are available:
No— the device operates in normal mode and transmits all events.
Entirely— the device does not execute system commands and does not participate in automation scenarios, and the system ignores alarms and other device notifications.
Lid only— the system ignores the device tamper triggering notifications.
Allows the user to disable events of the device until the first disarm.
Three options are available:
No— the device operates in normal mode.
Lid only— notifications on the device tamper triggering are disabled while the armed mode is active.
Entirely— the device is completely excluded from the operation of the system while the armed mode is active. The device does not execute system commands and does not report alarms or other events.
Ajax system allows you to set up a keypad code, as well as personal codes for users added to the hub.
With theOS Malevich 2.13.1update, we have also added the ability to create access codes for people who are not added to the hub. This is convenient, for example, to provide a cleaning company with access to security management.
With theOS Malevich 2.17update, codes for the rapid response units are available. The RRU codes are activated after the alarm and are valid for a specified period. See how to set up and use each type of code below.
To set keypad code
Go to keyboard settings.
SelectKeypad Code.
Set the keypad code you want.
To set the keypad duress code
Go to keypad settings.
SelectDuress Code.
Set the keypad duress code you want.
To set a personal code in the Ajax app
Go to the user profile settings (Hub→Settings→Users→Your profile settings).
SelectPasscode Settings(User ID is also visible in this menu).
SetUser CodeandDuress Code.
Each user sets a personal code individually. The admin cannot set a code for all users.
To set up an access code for a person who is not registered in the system
Go to the hub settings (Hub→Settings).
SelectKeypad Access Codes.
Set upUsernameandAccess Code.
If you want to set up a duress code, change settings for access to groups, Night Mode, code ID, temporarily disable or delete this code, select it in the list and make changes.
PRO or a user with admin rights can set up an access code or change its settings. This function is supported by hubs with OS Malevich 2.13.1 and higher. Access codes are not supported by the Hub (2G) Jeweller control panel.
To set up the RRU code
Only a PRO with the rights to configure the system can create and configure the RRU codes in theAjax PRO apps. More information about configuring this feature you can find inthis article.
The RRU codes are supported by hubs (except the Hub (2G) Jeweller model) with OS Malevich 2.17 and higher.
Adding passes and tags
KeyPad Plus Jeweller can work withTag key fobs,Pass cards, and third-party cards and key fobs that use DESFire® technology.
Before adding third-party devices that support DESFire®, make sure they have enough free memory to handle the new keypad. Preferably, the third-party device should be pre-formatted.
The maximum number of connected passes/tags depends on the hub model. At the same time, the bound passes and tags do not affect the total limit of devices on the hub.
Hub model
Number of Tag or Pass devices
Hub (4G) Jeweller
50
Hub Plus Jeweller
99
Hub 2 Jeweller
50
Hub 2 Plus Jeweller
200
Superior Hub Hybrid
50
The procedure for connecting Tag, Pass, and third-party devices is the same. See the connecting instructionshere.
Controlling security via codes
You can controlNight Mode, security of the entire facility or separate groups using general, personal, RRU, and access codes (configured by PRO or a user with admin rights). The keypad allows you to use 4 to 6 digit codes. Incorrectly entered numbers can be cleared with thebutton.
If a personal code or access code is used, the name of the user who armed or disarmed the system is displayed in the hub event feed and in the notifications list. If a general code is used, the name of the user who changed the security mode is not displayed.
Keypad access codesare supported by hubs (except theHub (2G) Jewellermodel) with OS Malevich 2.13.1 and higher.
TheRRU codesare supported by hubs (except theHub (2G) Jewellermodel) with OS Malevich 2.17 and higher.
Arming with a personal code
Theusernameis displayed in the notifications and events feed
Arming with a general code
Thedevice nameis displayed in the notifications and events feed
KeyPad Plus Jeweller is locked for the time specified in the settings if an incorrect code is entered three times in a row within 1 minute. The corresponding notifications are sent to users and to the monitoring station of the security company. A user or PRO with administrator rights can unlock the keypad in the Ajax app.
Controlling security at the object via general code
Activate the keypad by swiping your hand over it. Bring Tag or Pass to the keypad pass/tag reader if theAuthorization confirmation with a passcodefeature is activated.
Enter thegeneral code.
Press thearming/disarming/Night Modekey.
For example: 1234 →
Group security management with a general code
Activate the keypad by swiping your hand over it. Bring Tag or Pass to the keypad pass/tag reader if theAuthorization confirmation with a passcodefeature is activated.
If a security group is assigned to KeyPad Plus Jeweller (in theGroup Managementfield in the keypad settings), you do not need to enter the group ID. To manage the security mode of this group, entering a general or personal code is sufficient.
If a group is assigned to KeyPad Plus Jeweller, you will not be able to manageNight Modeusing a general code. In this case,Night Modecan only be managed using a personal code if the user has the appropriate rights.
Security management of the facility using a personal code
Activate the keypad by swiping your hand over it. Bring Tag or Pass to the keypad pass/tag reader if theAuthorization confirmation with a passcodefeature is activated.
Activate the keypad by swiping your hand over it. Bring Tag or Pass to the keypad pass/tag reader if theAuthorization confirmation with a passcodefeature is activated.
Enter theUser ID.
Press the * (Functionbutton).
Enter yourpersonal code.
Press the * (Functionbutton).
Enter theGroup ID.
Press thearming/disarming/Night Modekey.
For example: 2 → * → 1234 → * → 5 →
If a group is assigned to KeyPad Plus Jeweller (in theGroup Managementfield in the keypad settings), you do not need to enter the group ID. To manage the security mode of this group, entering a personal code is sufficient.
A duress code allows you to simulate alarm deactivation. The Ajax app and sirens installed at the facility will not give the user away in this case, but the security company and other users will be warned about the incident. You can use both a personal and a general duress code. InKeypad Access Codes, you can also set up a duress code for people not registered in the system.
Scenarios and sirens react to disarming under duress in the same way as to normal disarming.
Activate the keypad by swiping your hand over it. Bring Tag or Pass to the keypad pass/tag reader if theAuthorization confirmation with a passcodefeature is activated.
Enter thegeneral duress code.
Press the disarming button.
For example:4321 →
To use a personal duress code of registered user
Activate the keypad by swiping your hand over it. Bring Tag or Pass to the keypad pass/tag reader if theAuthorization confirmation with a passcodefeature is activated.
Enter theUser ID.
Press the * (Functionbutton).
Enter thepersonal duress code.
Press the disarming button.
For example:2 → * → 4422 →
To use a duress code of a person who is not registered in the system
Enter theduress codeset inKeypad Access Codesand press thedisarming key.
For example:4567 →
Using the RRU code
The RRU code is activated after triggering the alarm during the time configured in the hub settings, and it is valid for a specified period. This ensures that such code will only be used in case of risk, unlike keypad or user codes.
Security control of the object using the RRU code:
EnterRRU Codeand press thearming / disarming/ Night Mode activationbutton.
For example: 1234→
Security control of the group using the RRU code:
EnterRRU Code, press*, enterGroup ID, and press thearming / disarming/ Night Mode activationbutton.
For example: 1234 →*→ 2→
Security management using Tag or Pass
Activate the keypad by swiping your hand over it. KeyPad Plus Jeweller will beep (if enabled in the settings) and turn on the backlight.
Note that the keypad can be activated automatically with theAuto-wake on Delay when Enteringfunction ifDelay When Enteringis set up. This function is supported by KeyPad Plus Jeweller with firmware version 6.60.0.6 or higher and hubs withOS Malevich 2.19or higher.
Bring Tag or Pass to the keypad pass/tag reader. It is marked with wave icons.
Enter the required code if theAuthorization confirmation with a passcodefeature is activated.
Press theArm,Disarm, orNight Modebutton on the keypad.
Note that ifEasy armed mode changeis enabled in the KeyPad Plus Jeweller settings, you do not need to press theArm,Disarm, orNight Modebutton. The security mode will change to the opposite after tapping Tag or Pass.
Security control of a single group
Tag or Pass can control the security mode of a single group. This is possible if KeyPad Plus Jeweller is not assigned to any group and Tag or Pass has no group restrictions.
To change the security mode of a single group using Tag or Pass:
Activate the keypad by swiping your hand over it. Bring Tag or Pass to the keypad pass/tag reader if theAuthorization confirmation with a passcodefeature is activated.
Press thearming / disarming/ Night Mode activationbutton.
For example:→ 01→
If the security mode is successfully changed, a short beep will sound, the indicator will change, and a notification with the username will appear in the event log.
Mute Interconnected Fire Detectors Alarms function
KeyPad Plus Jeweller can mute an interconnected fire alarm by pressing theFunctionbutton (if the required setting is enabled). The reaction of the system to pressing a button depends on the settings and the state of the system:
Interconnected Fire Detectors Alarms have already propagated— by the first press of the button, all sirens of the fire detectors are muted, except for those that registered the alarm. Pressing the button again mutes the remaining detectors.
Interconnected alarms delay time lasts— by pressing theFunctionbutton, the siren of the triggeredAjax fire detectorsis muted.
KeyPad Plus Jeweller can report the current security mode, keystrokes, malfunctions, and its status by LED indication and sound. The current security mode is displayed by the backlight after the keypad is activated. The information about the current security mode is relevant even if the arming mode is changed by another device: a key fob, another keypad, or an app.
Auto-wake on Delay when Enteringfunction allows automatically activating the keypad whenDelay When Enteringis set up. This function is supported by KeyPad Plus Jeweller with firmware version 6.60.0.6 or higher and hubs withOS Malevich 2.19or higher.
You can activate the keypad by swiping your hand over the touch panel from top to bottom. When activated, the backlight on the keypad will turn on and a beep will sound (if enabled).
Event
Indication
There is no connection to the hub or radio signal range extender
LEDXblinks
KeyPad Plus Jeweller body is open (SmartBracket mount is removed)
LEDXblinks briefly once
Touch button pressed
Short beep, the current system security status LED blinks once. The volume depends on the keypad settings
The system is armed
Short beep,ArmedorNight ModeLED lights up
The system is disarmed
Two short beeps, theDisarmedLED lights up
An incorrect code was entered or there was an attempt to change security mode by an unconnected or deactivated pass/tag
Long beep, digital unit LED backlight blinks 3 times
The security mode cannot be activated (for example, a window is open and theSystem integrity checkis enabled)
Long beep, the current security status LED blinks 3 times
The hub does not respond to the command — there is no connection
Long beep,X(Malfunction)LED lights up
The keypad is locked due to a wrong code attempt or attempt to use an unauthorised pass/tag
Long beep, during which the security status LEDs and keypad backlight blink 3 times
The batteries are low
After changing the security mode, theX LED lights up. The touch buttons are locked for this time.
When you try to turn on the keypad with discharged batteries, it emits a long beep, theXLED smoothly lights up and goes off, then the keypad turns off
The system requires to confirm authorization with a password after access devices’ confirmation. Available if theAuthorization confirmation with a passcodefeature is activated
The current security status LED blinks during the set time for confirmation
Sound notifications of malfunctions
If any device is offline or the battery is low, KeyPad Plus Jeweller can notify system users with an audible sound. The keyboards’ LEDsХwill blink. Malfunction notifications will be displayed in the events feed, SMS text, or push notification.
To enable sound notifications of malfunctions, use Ajax PRO and PRO Desktopapps:
ClickDevices, choose hub and open its settings: ClickService→Sounds and Alerts
Enable toggles:If battery of any device is lowandIf any device is offline.
ClickBackto save settings.
Sound notifications of malfunctions settings are available for all hubs (except the Hub model) with firmware version OS Malevich 2.15 or higher.
Sound notifications of malfunctions are supported by KeyPad Plus Jeweller with firmware version 5.57.5.0 or higher.
Event
Indication
Note
If any device is offline.
Two short sound signals,MalfunctionindicatorХblinks twice.
Beep once per minute until all devices in the system are online.
Users can delay sound indication for 12 hours.
If KeyPad Plus is offline.
Two short sound signals,MalfunctionindicatorХblinks twice.
Beep once per minute until the keyboard in the system is online.
It’s impossible to delay sound indication.
If battery of any device is low.
Three short sound signals,MalfunctionindicatorХblinks three times.
Beep once per minute until the battery is restored or the device is removed.
Users can delay sound indication for 4 hours.
Sound notifications of malfunctions appear when the keypad indication is finished. If several malfunctions occur in the system, the keypad will notify about the loss of connection between the device and the hub first.
Functionality testing
The Ajax system provides several types of tests that help you make sure that installation points of devices are selected correctly.
KeyPad Plus Jeweller functionality tests do not start straight away but after no more than one hub-detector ping period (36 seconds when using the standard hub settings). You can change the ping period of devices in theJewellermenu of the hub settings.
Tests are available in the device settings menu (Ajax App → Devices→ KeyPad Plus Jeweller → Settings)
KeyPad Plus Jeweller is best placed indoors near the entrance. This allows disarming the system before the entry delays have expired, as well as quickly arming the system when leaving the premises.
When holding KeyPad Plus Jeweller in your hands or using it on a table, we cannot guarantee that the touch buttons will work properly.
It is a good practice to install the keypad 1.3 to 1.5 meters above the floor for convenience. Install the keypad on a flat, vertical surface. This allows KeyPad Plus Jeweller to be firmly attached to the surface and to avoid false tamper triggering.
Besides, the placement of the keypad is determined by the distance from the hub or the radio signal range extender, and the presence of obstacles between them that prevent the passage of the radio signal: walls, floors, and other objects.
Be sure to check the Jeweller signal strength at the installation site. If the signal strength is low (a single bar), we cannot guarantee a stable operation of the security system. At the very least, relocate the device as repositioning even by 20 cm can significantly improve the signal reception.
In places where parts of clothing (for example, next to the hanger), power cables, or Ethernet wire may obstruct the keypad. This can lead to false triggering of the keypad.
Inside premises with temperature and humidity outside the permissible limits. This could damage the device.
In places where KeyPad Plus Jeweller has an unstable or poor signal strength with the hub or radio signal range extender.
Within 1 meter of a hub or radio signal range extender.
Close to electrical wiring. This may cause communication interferences.
Outdoors. This could damage the device.
Installing the keypad
Prior to installing KeyPad Plus Jeweller, be sure to select the optimal location following the requirements of this manual.
Attach the keypad to the surface with double-sided adhesive tape and carry outsignal strengthandattenuation tests. If the signal strength is unstable or if one bar is displayed, move the keypad or use theradio signal range extender.
Double-sided adhesive tape may only be used for temporary attachment of the keypad. The device attached with adhesive tape can at any time be detached from the surface and fall, which may lead to failure.
Please note that if the device is attached with adhesive tape, the tamper will not trigger when trying to detach it.
Check the convenience for code entry using Tag or Pass to manage security modes. If it is inconvenient to manage the security at the selected location, relocate the keypad.
Remove the keypad from the SmartBracket mounting plate.
Attach the SmartBracket mounting plate to the surface using the bundled screws. When attaching, use all fixing points. Be sure to fix the perforated corner on the SmartBracket plate so that the tamper responds to a detachment attempt.
Slide KeyPad Plus Jeweller onto the mounting plate and tighten the mounting screw at the bottom of the body. The screw is needed for more reliable fastening and protection of the keypad from quick dismantling.
As soon as the keypad is fixed on the SmartBracket, it shall blink once with LEDX — this is a signal that the tamper has been triggered. If the LED does not blink after installation on SmartBracket, check the tamper status in the Ajax app, and then make sure the plate is firmly attached.
Maintenance
Check the functioning of your keypad on a regular basis. This can be done once or twice a week. Clean the body from dust, cobwebs, and other contaminants as they emerge. Use a soft dry cloth that is suitable for equipment care.
Do not use substances that contain alcohol, acetone, gasoline or other active solvents to clean the detector. Wipe the touch keypad gently: scratches can reduce the sensitivity of the keypad.
The batteries installed in the keypad provide up to 3.5 years of autonomous operation at default settings. If the battery is low, the system sends appropriate notifications, and theX (Malfunction) indicator smoothly lights up and goes out after each successful code entry.
KeyPad Plus Jeweller can work up to 2 months after the low battery signal. However, we recommend you replace the batteries immediately upon notification. It is advisable to use lithium batteries. They have a large capacity and are less affected by temperatures.
The warranty for the Limited Liability Company “Ajax Systems Manufacturing” products is valid for 2 years after purchase and does not extend to the bundled batteries.
If the device does not function properly, we recommend that you first contact the support service as half of the technical issues can be resolved remotely.
Curtain Outdoor Jewelleris a wireless curtain-type motion detector with dual motion detection technology for outdoor and indoor use. The detector has a horizontal detection angle of 8° and is designed for the perimeter control: windows, doorways, and other entrances or exits of the guarded facility. It detects motion at a distance of up to 12 m.
Curtain Outdoor Jeweller communicates with the hub using two secure protocols. The detector usesJewellerto transmit alarms and events andWingsto update the firmware. The communication range in an open space is up to 1,700 m. Pre-installed batteries ensure up to 3 years of autonomous operation.
Curtain Outdoor Jeweller is compatible withReX Jeweller. However, when connected to ReX Jeweller, firmware updates are unavailable because the detector uses theWingsprotocol.
You can manage the detector and its settings using iOS, Android, macOS, and Windowsapps. The system notifies users of any events via push notifications, SMS, or calls.
Functional elements
Detector
LED indicator.
Motion detector’s lens.
Masking sensor.
Power button.
Tamper button. It triggers in case of an attempt to detach the detector from the surface or remove it from the mounting panel.
QR code with the device ID. It is used to add the detector to the hub.
Slider for adjusting the motion detection distance.
SmartBracket mounting panel. To remove the panel, slide it down.
Perforated part of the mounting panel. Triggers a tamper in case of any attempt to detach the detector from the surface. Do not break it off.
Fixing points for attaching the SmartBracket mounting panel to the surface, angle or third-party mount.
Holding screw for securing the detector on SmartBracket.
The detector’s lens optical center mark for easy device installation.
Angle mount
Fixing points for attaching the angle mount to the surface.
Fixing points for attaching the SmartBracket mounting panel or hood to the angle mount.
Hood
The hood protects masking sensors from rain and snow. It is used when the detector cannot be installed under the cover.
Fixing points for attaching the hood to the surface and angle or third-party mount.
Perforated part of the hood. Triggers a tamper in case of any attempt to detach the detector from the surface. Do not break it off.
The detector’s lens optical center mark for easy device installation.
The hole for securing the detector on the hood with a holding screw.
Operating principle
Two parallel IR sensors of Curtain Outdoor Jeweller register intrusion upon detecting moving objects with a temperature different from the ambient.
When the device detects motion, it additionally performs a radio frequency (RF) scan with a built-in K-band microwave sensor. It helps to eliminate false alarms caused by thermal interference: air flows, fans, air conditioners, etc.
In case of an alarm, a detector instantly sends it to the hub. Therefore, the hub activates thesirensconnected to the system, runs thescenarios, and notifies users and the security company. All Curtain Outdoor Jeweller alarms and events are recorded in the events feed of Ajax apps.
Users and the monitoring company know exactly where motion is detected. The notifications contain the name of aspace(the name of a guarded facility), the device name, and the virtual room to which the detector is assigned.
The detector doesn’t switch to the armed mode instantly. The switching time depends on two factors: the exit delay (specified in the detector settings) and the hub–detector polling interval (JewellerorJeweller/Fibrasettings, the default value is 36 s). In the first case, the delay is set by an admin or a PRO-user with admin rights. In the second case, the delay occurs because it takes one polling interval for the hub to notify the detector about switching to the armed mode.
Curtain Outdoor Jeweller uses the SmartDetect algorithm to protect against false alarms. This algorithm allows the detector to analyze the thermal diagram read by the sensor: the intensity of infrared radiation, size of the heat spot, time spent in the detection area, and other parameters.
After this stage, an additional RF scan of the room is run using the built-in K-band microwave sensor. Depending on the result, the alarm is activated or not.
Curtain Outdoor Jeweller has theCorrelation signal processingfeature to prevent false alarms. It is enabled by default in the detector settings. When the feature is enabled, the detector activates the RF sensor only if both IR sensors register identical signals. If it is disabled, Curtain Outdoor Jeweller runs an RF scan when at least one of the two IR sensors detects thermal radiation.
When properly installed and configured, Curtain Outdoor Jeweller will not respond to pets up to 1 m (100 cm) in height. We recommend installing the detector at a height of 1 m, adjusting the slider on the detector enclosure to thePetposition, and setting up thePet immunedetection mode in the app.
Due to temperature compensation, the detector responds to movements, even if the indoor or outdoor temperature is close to the human body temperature. Read more about temperature compensation in thearticle.
Anti-masking system
Masking is an attempt to block the view of the detector. Curtain Outdoor Jeweller detects the following types of masking:
An obstacle in front of the detector’s lens at a distance of up to 5 cm. The maximum distance depends on the material.
Painting over the detector’s lens.
Taping the detector’s lens.
The system notifies users and the security company’s monitoring station about masking. The maximum masking detection time is 180 s (depending on the obstacle type and the distance to it).
If theAnti-maskingfeature is enabled, it is always active and works regardless of the security mode.
Jeweller and Wings are wireless data transfer protocols that provide fast and reliable two-way communication between the hub and devices. The detector usesJewellerto transmit alarms and events andWingsto update the firmware.
The Ajax system can transmit alarms to thePRO Desktopmonitoring app, as well as to the central monitoring station (CMS), in formats ofSurGard (Contact ID), SIA (DC-09), ADEMCO 685, andother protocols.
Curtain Outdoor Jeweller can transmit the following events:
Motion alarm.
Masking.
Alert if moved.
Tamper alarm/recovery.
Loss/restoration of connection with the hub.
Permanent deactivation/activation of the device.
One-time deactivation/activation of the device.
When an alarm is received, the operator at the security company’s monitoring station knows what happened and precisely where to dispatch a rapid response unit. The addressability of Ajax devices allows sending events to PRO Desktop or the CMS, including the device’s type and name, security group, and virtual room. Note that the list of transmitted parameters may vary depending on the CMS type and the selected communication protocol for the monitoring station.
Protection against faster battery discharging
TheNotify on risk of fast battery dischargefeature is available on devices operating with hubs withOS Malevich 2.27or later.
To prevent rapid battery discharge, Curtain Outdoor Jeweller has theNotify on risk of fast battery dischargesetting. Once the system detects that the device is installed incorrectly, system users will receive notifications in Ajax apps, and similar information will be displayed in the device states.
The device sensors can be triggered by different objects or obstacles, which the device filters out as unconfirmed alarms. Also, the device requires more power to process each triggering. As a result, when the number of such triggerings gets too high, the system will notify about increased power consumption and risk of fast battery discharge.
Enable theNotify on risk of fast battery dischargefeature in the device settings to save the battery charge.
Consider changing the device placement if you receive a notification about incorrect installation.
The hub and the device operating at different radio frequencies are incompatible. The radio-frequency range of the device may vary by region. We recommend purchasing and using Ajax devices in the same region. You can check the range of operating radio frequencies with thetechnical support service.
Open theAjax app. Select aspacewhere you want to add the detector.
Go to theDevicestab and clickAdd Device.
Name the device, scan, or type in the QR code (placed on the detector and the package box), and select a room and a group (ifGroup modeis enabled).
ClickAdd— the countdown will begin.
Switch on the device by holding the power button for 3 seconds.
Once added to the hub, the detector will appear in the list of hub devices in the Ajax app. The device status update frequency in the list depends on theJewellerorJeweller/Fibrasettings with the default value of 36 s.
If the connection fails, try again in 5 seconds. If the maximum number of devices is added to the hub, you will be notified when trying to add a new one.
Curtain Outdoor Jewellerworks with only one hub. Once the device is connected to a new hub, it stops sending events to the old one. Adding the detector to a new hub does not automatically remove it from the device list of the old hub. This must be done using the Ajax app.
Malfunctions
When the device detects a malfunction (for example, there is no connection via the Jeweller protocol), a malfunction counter is displayed in the Ajax app in the upper left corner of the device icon.
All malfunctions can be seen in the deviceStates. Fields with malfunctions will be highlighted in red.
Malfunction is displayed if:
The device temperature is outside acceptable limits.
The device lid is open (tamper is triggered).
No connection with the hub or radio signal range extender via Jeweller.
No connection with the hub or radio signal range extender via Wings.
The calibration of the masking sensor failed.
The accelerometer of the device is faulty.
The detector battery is low.
Icons
The icons in the app display some Curtain Outdoor Jeweller states. To access them:
Curtain Outdoor Jeweller is an outdoor detector, and its temperature is not considered when calculating the average temperature in the room to which the detector is assigned.
The status of the detector tamper that responds to detachment or opening of the device enclosure:
Open— the detector is removed from the SmartBracket mounting panel, or its integrity is compromised. Check the mounting of the detector.
Closed— the detector is installed on the SmartBracket mounting panel. The integrity of the device enclosure and the mounting panel is not compromised. Normal state.
Shows the status of the device’s permanent deactivation setting:
No— the device operates in normal mode and transmits all events.
Lid only— the hub administrator has disabled notifications about tamper triggering.
Entirely— the device is entirely excluded from the operation of the system. The device does not execute system commands and does not report alarms or other events.
By number of alarms— the device is automatically disabled when the number of alarms is exceeded (theDevices auto deactivationsetting). The feature is configured in Ajax PRO apps.
By timer— the device is automatically disabled by the system when the recovery timer expires (theDevices auto deactivationsetting). The feature is configured in Ajax PRO apps.
One-time deactivation
Shows the status of the device’s one-time deactivation setting:
No— the device operates in normal mode.
Entirely— the device is completely excluded from the operation of the system until the system is disarmed for the first time. The device does not execute system commands or report alarms and other events.
Lid only— notifications of the tamper triggering are disabled until the system is disarmed for the first time.
Instant alarm— the armed detector immediately reacts to a threat and raises the alarm.
Entry/Exit— when a delay is set, the armed device starts the countdown and doesn’t raise the alarm even if triggered until the countdown ends.
Follower— the detector inherits the delays fromEntry/Exitdetectors. However, when theFolloweris triggered individually, it immediately raises the alarm.
Delay when entering
Delay when entering (alarm activation delay) is the time the user has to disarm the security system after entering the premises.
Entry delay time inNight Mode. Delay when entering (alarm activation delay) is the time the user has to disarm the security system after entering the premises.
Detector name. Displayed in the list of hub devices, text of SMS and notifications in the events feed.
To change the detector name, click on the text field.
The name can contain up to 12 Cyrillic characters or up to 24 Latin characters.
Room
Selecting the virtual room to which Curtain Outdoor Jeweller is assigned.
The room name is displayed in the text of SMS and notifications in the events feed.
Sensitivity
Sensitivity level of the motion detector. The choice depends on the type of the object, the presence of probable sources of false alarms, and the specifics of the protected area:
Low— there are likely sources of false alarms in the protected area. For example, tall bushes.
Medium(by default) — recommended value, suitable for most objects. Do not change it if the detector works correctly.
High— there is no interference in the protected area; the maximum detection distance and the alarm detection speed are important. For example, if the detector is installed in a narrow passage.
Detection mode
Device reaction to motion, depending on object and device placement:
Pet immune— for premises with pets. The recommended device installation height is1 m. The slider on the enclosure has to be set to thePetposition.
Near— appropriate for short-range intrusion detection. The recommended device installation height is2.4 m. The slider on the enclosure has to be set to theNearposition.
Far(by default) — appropriate for long-range intrusion detection. The recommended device installation height is2.4 m. The slider on the enclosure has to be set to theFarposition.
Alarm LED indication
When disabled, the LED indicator doesn’t notify about alarms and tamper triggering.
Always active
When enabled, the detector is always in the armed mode and detects motion.
When enabled, the system raises the alarm if the device is moved or detached from the mounting panel.
Accelerometer sensitivity
The sensitivity level of the detector’s accelerometer. The selection depends on the type of the object, the presence of probable sources of false alarms, and the specifics of the protected area:
Low— there are likely sources of false alarms in the protected area. For example, vibration from passing trucks.
Medium(by default) — recommended value, suitable for most objects. Do not change it if the detector works correctly.
High— there is no interference in the protected area; the maximum detection distance and the alarm detection speed are important.
Notify on risk of fast battery discharge
Available on devices operating with hubs withOS Malevich 2.27or later.
When this option is enabled, the user is notified when incorrect installation affects the device’s battery life because the detector is often triggered without an actual intrusion.
Alert with a siren
If motion detected
When this option is enabled,sirensconnected to the systemare activated when motion is detected by Curtain Outdoor Jeweller.
If masking detected
When this option is enabled,sirensconnected to the systemare activated when Curtain Outdoor Jeweller detects masking
The field is displayed and active if theAnti-maskingoption is enabled.
If device was moved
When this option is enabled, the built-in accelerometer alerts about sabotage.Sirensadded to the systemare activated when Curtain Outdoor Jeweller is moved.
The field is displayed and active ifAlert if movedis enabled.
Alarm reaction
Operating mode
Specify how this device will react to alarms:
Instant alarm— the armed detector immediately reacts to a threat and raises the alarm.
Entry/Exit— when a delay is set, the armed device starts the countdown and doesn’t raise the alarm even if triggered until the countdown ends.
Follower— the detector inherits the delays fromEntry/Exitdetectors. However, when theFolloweris triggered individually, it immediately raises the alarm.
Delay when entering
Selecting delay time when entering: 5 to 120 s.
Delay when entering (alarm activation delay) is the time the user has to disarm the security system after entering the premises.
Opens the Curtain Outdoor Jeweller user manual in the Ajax app.
Permanent deactivation
Allows the user to deactivate the device without removing it from the system.
Three options are available:
No— the device operates in normal mode and transmits all events.
Entirely— the device does not execute system commands and does not participate in automation scenarios, and the system ignores alarms and other device notifications.
Lid only— the system ignores notifications about the device tamper triggering.
Allows the user to disable device events until the system is disarmed for the first time.
Three options are available:
No— the device operates in normal mode and transmits all events.
Entirely— the device is completely excluded from the operation of the system until the system is disarmed for the first time. The device does not follow system commands and does not report alarms or other events.
Lid only— notifications of the tamper triggering are disabled until the system is disarmed for the first time.
Downloading the updated firmware version of the detector.
Flashes green 2 times every second.
Updating the detector firmware. The indication lasts during the firmware update.
Functionality testing
The Ajax system offers several types of tests to help choose the correct installation place for the devices. Testing does not start immediately. However, the waiting time does not exceed the duration of one hub–device polling interval. The polling interval can be checked and configured in hub settings (Hub→Settings→JewellerorJeweller/Fibra).
Curtain Outdoor Jeweller is suitable for protecting the area around the guarded facility. It allows you to secure the perimeter, leaving space for free movement inside. The detector can be installed both outdoors and indoors.
Curtain Outdoor Jeweller can protect:
Front doors.
Windows.
Gates.
Fences.
Arches and other places where you need to protect the perimeter or passage.
The detector is located at a height of 2.4 mfrom the ground level. For thePet immunityfeature to be effective, the detector should be installed at a height of1 m from the ground level. The recommended height is specified relative to the optical center of the detector’s lens. It is marked by the intersection of two lines on the device’s mounting panel or hood.
If you install the detector at a height other than the recommended one, ensure there are no false alarms caused by pets, the device detects people’s motion, and the detection zone meets your needs.
If the surface is not flat, the installation height is calculated from the highest point of the area to be protected.
The detector should be installed on a flat, stable surface, for example, on the wall of a house or a solid fence. Installing the detector on a shaky (unstable) surface will result in false alarms. The detector enclosure must be placed perpendicular to the ground level, and the intended path of the intruder must be perpendicular to the axis of the detector’s lens.
When choosing where to place Curtain Outdoor Jeweller, consider the parameters that affect its operation:
Motion detection zone.
Jeweller and Wings signal strength.
Distance between the detector and the hub or range extender.
The presence of obstacles between devices that can affect the radio signal, such as walls, inter-floor ceilings, or large objects located in the premises.
The presence of bushes, trees, air conditioners, glass, and other constructions that can block the detector’s view.
The presence of water reservoirs or pools in the detection area. They can cause false alarms.
Consider the recommendations for detector placement when developing a security system project for the facility. The security system must be designed and installed by specialists. The list of recommended Ajax partners isavailable here.
Signal strength
The signal strength is determined by the number of undelivered or corrupted data packages over a certain period of time. The iconin theDevicestab in Ajax apps indicates the signal strength:
three bars— excellent signal strength;
two bars— good signal strength;
one bar— low signal strength, stable operation is not guaranteed;
crossed out icon— no signal.
Check the Jeweller and Wings signal strength before final installation. With a signal strength of one or zero bars, we do not guarantee the device will operate stable. Consider relocating the device, as adjusting its position even by 20 cm can significantly improve the signal strength. If the signal remains poor or unstable after relocation, consider using aradio signal range extender.
Detection zone
When choosing where to place the detector, perform thedetection zone testto accurately determine the sector in which the device detects motion.
The detection distance is adjusted using theDetection modeslider on the detector’s rear side.
Position of the Detection mode slider
Motion detection distance
Far
Up to 12 m
Near
Up to 8 m
Pet
Up to 12 m
When choosing the installation site, consider the detector’s horizontal viewing angle and the width of the detection zone. Incorrect placement of the detector may cause false alarms.
Motion detection distance
Detection zone width (beam)
Up to 12 m
1.68 m
Up to 8 m
1.12 m
Do not install the detector
Nearby any metal objects or mirrors that can cause signal attenuation and screening.
Opposite trees or bushes in the detection zone of both IR sensors of the detector.
In front of furniture, glass, or other constructions that may block the detector’s view.
In places where electrical panels, air conditioning units, downspout pipes, or other constructions are located in the device’s detection zone.
In front of water reservoirs or pools if they are located in the detection zone of the detector.
In places with low or unstable Jeweller and/or Wings signal strength.
Closer than 1 m to the hub or radio signal range extender.
Installation
Before installing Curtain Outdoor Jeweller, ensure that you have chosen the optimal location that complies with the requirements of this manual.
Use theInstallation templateto prepare holes for mounting the device’s SmartBracket or angle mount on the surface.
There are four options for installing Curtain Outdoor Jeweller:
To the SmartBracket mounting panel. SmartBracket allows you to install the detector on a vertical surface.
To the hood. The hood for Curtain Outdoor Jeweller protects masking sensors from rain and snow. It is used when the detector cannot be installed under the cover and allows you to install the detector on a vertical surface.
The hood replaces the detector’s SmartBracket mounting panel, so you need to remove it before installing the detector with the hood.
To the angle mount. It allows you to install the detector parallel to the guarded facility’s wall. The detector can be installed to the angle mount with the SmartBracket mounting panel or hood.
To a third-party mount. The detector can be installed to a third-party mount with the SmartBracket mounting panel or hood.
When using a third-party mount, ensure that Curtain Outdoor Jeweller is fixed vertically. Deviation from the vertical axis affects the detection area of the detector.
Before installation, set the required detection mode in the detectorsettingsand on its enclosure.
To install the detector:
Remove the SmartBracket mounting panel from the detector. Unscrew the holding screw first and slide the panel down.
Fix the SmartBracket panel or hood using double-sided adhesive tape or other temporary fasteners. The hood or mounting panel can be installed on a vertical surface or in a corner of the premises using the mount angle.
Therecommended installation height is 2.4 m or 1 m(to protect against false alarms caused by pets) relative to the optical center of the detector’s lens.
SmartBracket and the hood have markings on the inner side for easy installation. The intersection of two lines marks the optical center of the device’s lens (not the mounting panel or hood). Orient them when installing the detector.
Double-sided adhesive tape can only be used for temporary installation. The device attached by the tape may come unstuck from the surface at any time. As long as the device is taped, the tamper will not be triggered when the device is detached from the surface.
Set theDetection modeslider on the device enclosure to the required position. Then, theDetection modesettingin the Ajax app should be set to the value appropriate for the slider position.
Installation height
Slider position
Detection mode
2.4 m
Far
Far
2.4 m
Near
Near
1 m
Pet
Pet immune
Mismatching the slider position to theDetection modesetting and the installation height may result in the device’s incorrect operation.
Place the detector on the SmartBracket mounting panel or hood and run theJeweller signal strength testandWings signal strength test. The recommended signal strength is two or three bars. With a signal strength of one or zero bars, we do not guarantee the device will operate stable. Consider relocating the device, as repositioning even by 20 cm can significantly improve the signal strength. If the signal remains poor or unstable after relocation, consider using aradio signal range extender.
Perform thedetection zone test. To check the motion detector, walk around the premises while observing the LED indicator and determine the detection zone of the detector. The maximum range of motion detection is 12 m. If the detector does not respond to movement during the test in 5 cases out of 5, relocate the device.
Remove the detector from the SmartBracket mounting panel or hood.
Use bundled screws to attach SmartBracket / the hood / the angle or third-party mount to the surface.
Use theInstallation templateto prepare holes for mounting the device’s SmartBracket or angle mount on the surface.
If the detector is installed directly to the hood or mounting panel, attach the device to them. When installing the detector to the angle or third-party mount, first attach the SmartBracket mounting panel or hood to the mount using bundled screws. Then, install the detector on the mounting panel or hood.
Leave the device’s detection zone (horizontal angle is 8°) and ensure there is no movement within the detector’s zone of view. This is necessary for the correct calibration of masking sensors. During calibration, the detector’s LED indicator will flash green every 0.5 sec. Calibration takes up to 2 minutes.
Calibration starts automatically after installing the detector on the mounting panel or hood.
Tighten the holding screw on the bottom of the detector enclosure. The screw is needed for more reliable fastening and protection of the detector from quick dismantling.
If the LED indicator is not activated after installing the detector on SmartBracket, check the tamper status in the Ajax app, the integrity of the fastening, and the tightness of the detector fixation on the panel. You will receive a notification if the detector is detached from the surface or removed from the mounting panel.
Maintenance
Regularly check the functioning of the detector. The optimal frequency of checks is once every three months. Clean the detector enclosure from dust, cobwebs, and other contaminants as they emerge. Use soft, dry wipes suitable for equipment maintenance.
Do not use substances that contain alcohol, acetone, gasoline, and other active solvents to clean the device.
Pre-installed batteries provide up to 3 years of the detector’s autonomous operation. When the battery is low, the system will send a corresponding notification to Ajax apps. In case of an alarm, the LED indicator will smoothly light up and go out.
Warranty for the Limited Liability Company “Ajax Systems Manufacturing” products is valid for 2 years after the date of purchase.
If you encounter any issues with the device’s functionality, we recommend contacting Ajax Technical Support first. In most cases, technical issues can be resolved remotely.
AJAX Trådlös rök- och värmedetektor FireProtect Vit
SKU: 367304827
€70,55€89,98
Enhetspris
Beskrivning av produkten
AJAX Wireless Smoke DetectorFireProtect med temperatursensor övervakar säkerheten i rummet 24 timmar om dygnet och rapporterar omedelbart rök och snabba temperaturstegringar.
Kan fungera fristående som en rökdetektor tack vare den inbyggda sirenen. Kontrollerar självständigt rökkammaren och meddelar omedelbart om det finns behov av dammborttagning.
Enheten upptäcker rök med hjälp av en kamera med en fotoelektrisk sensor. Men om rök ännu inte avges registrerar detektorn en ökning av rumstemperaturen.
Redo att användas direkt ur lådan: batteriet är redan insatt, så det finns inget behov av att demontera detektorn. Med ett klick kan den anslutas till kontrollpanelen via mobilappen. Den kan monteras på SmartBracket-fästet på bara några minuter.
Typ av detektor.
Installation: Inomhus
Kompatibilitet: Med alla Ajax Hubs, men kan även användas som en fristående enhet
Avkänningselement: Fotoelektrisk sensor och temperatursensor
Aktiveringströskel: +59°C ±2°C
Meddelandetyper: Ljud/ljus
Volym för inbyggd siren: 85 dB
Larmhastighet: 0,15 s
Filter för falsklarm: Ja
Strömförsörjning: Två CR2-batterier, 3 V
Ersättningsbatteri: CR2032
Batteriets livslängd: 4 år
Ingen garanti på batterier
Drifttemperatur: 0°C till +65°C
Luftfuktighet: Upp till 80%.
Test och inställningar på distans: Ja
Mått: 132 × 132 × 31 mm
Vikt: 220 g
Installationsanvisningar finns i Ajax-appen, som öppnas när du skannar detektorns QR-kod under installationen. Enkel installation och anslutning till Ajax Hub.
AJAX Trådlös rörelsedetektor för inomhusgardiner MotionProtect Gardin Vit
SKU: 367304851
€70,55€89,98
Enhetspris
Gardindetektor för inomhusbrukMotionProtect Curtain är lämplig för installation vid dörrar, fönster och grindar. Detekteringsområde 15 m.
Fungerar endast med en av Ajax säkerhetspaneler.
Tillförlitligt perimeterskydd.
Skydd för garage.
Fungerar även vid -10°C .
Kan med rätt installation även installeras om du har husdjur.
Typ av detektor.
Justerbar från 6 till 15 m
Installation: Inomhus
Kompatibilitet: Med alla Ajax-kontrollpaneler
Larmets överföringstid: 0,15 sekunder
Detekteringsvinkel:
Horisontellt - 6°
Vertikal - 90
Hastighet för rörelsedetektering: 0,3 till 2 m/s
Rekommenderad installationshöjd: 2,4 m
Strömförsörjning: CR123A-batterier, 3 V, upp till 3 år
Kommunikationsavstånd med annan utrustning: upp till 1 700 m i öppna miljöer
Driftstemperatur: -10°C till +40°C
Storlek: 134 × 44 × 34 mm
Vikt: 118 g
Ingen garanti på batterier.
Installationsanvisningar finns i Ajax-appen, som öppnas när du skannar detektorns QR-kod under installationen. Enkel installation och anslutning till Ajax Hub.
Tillgänglig för hämtning på
Slut i lager på
Tillagd för jämförelse
Gräns på count_product-produkt uppnådd
Tillagd för jämförelse
Gräns på count_product-produkt uppnådd
{"id":41613546913975,"title":"Default Title","option1":"Default Title","option2":null,"option3":null,"sku":"367304850","requires_shipping":true,"taxable":true,"featured_image":null,"available":true,"name":"AJAX MotionProtect Curtain Trådlös rörelsedetektor för inomhusbruk i svart","public_title":null,"options":["Default Title"],"price":7055,"weight":0,"compare_at_price":8998,"inventory_management":"shopify","barcode":null,"requires_selling_plan":false,"selling_plan_allocations":[],"quantity_rule":{"min":1,"max":null,"increment":1}}
AJAX MotionProtect Curtain Trådlös rörelsedetektor för inomhusbruk i svart
SKU: 367304850
€70,55€89,98
Enhetspris
Gardindetektor för inomhusbrukMotionProtect Curtain är lämplig för installation vid dörrar, fönster och grindar. Detekteringsområde 15 m.
Fungerar endast med en av Ajax säkerhetspaneler.
Tillförlitligt perimeterskydd.
Skydd för garage.
Fungerar även vid -10°C.
Kan med rätt installation även installeras om du har husdjur.
Typ av detektor.
Justerbar från 6 till 15 m
Installation: Inomhus
Kompatibilitet: Med alla Ajax-kontrollpaneler
Larmets överföringstid: 0,15 sekunder
Detekteringsvinkel:
Horisontellt - 6°
Vertikal - 90
Hastighet för rörelsedetektering: 0,3 till 2 m/s
Rekommenderad installationshöjd: 2,4 m
Strömförsörjning: CR123A-batterier, 3 V, upp till 3 år
Kommunikationsavstånd med annan utrustning: upp till 1 700 m i öppna miljöer
Driftstemperatur: -10°C till +40°C
Storlek: 134 × 44 × 34 mm
Vikt: 118 g
Ingen garanti på batterier.
Installationsanvisningar finns i Ajax-appen, som öppnas när du skannar detektorns QR-kod under installationen. Enkel installation och anslutning till Ajax Hub.
Tillgänglig för hämtning på
Slut i lager på
Tillagd för jämförelse
Gräns på count_product-produkt uppnådd
Tillagd för jämförelse
Gräns på count_product-produkt uppnådd
{"id":41613546193079,"title":"Default Title","option1":"Default Title","option2":null,"option3":null,"sku":"367304848","requires_shipping":true,"taxable":true,"featured_image":null,"available":true,"name":"AJAX MotionCam Trådlös rörelsedetektor för inomhusbruk med fotoverifiering Vit","public_title":null,"options":["Default Title"],"price":14622,"weight":0,"compare_at_price":17246,"inventory_management":"shopify","barcode":"856963007699","requires_selling_plan":false,"selling_plan_allocations":[],"quantity_rule":{"min":1,"max":null,"increment":1}}
AJAX MotionCam Trådlös rörelsedetektor för inomhusbruk med fotoverifiering Vit
SKU: 367304848
€146,22€172,46
Enhetspris
MotionCam trådlös rörelsedetektor med fotoverifiering.
Fungerar endast med AJAX kontrollpanelHub 2 ellerHub 2 Plus.
Skickar en verifieringsbild till användaren på 9 sekunder.
Med MotionCam får du reda på den faktiska situationen i hemmet redan innan tjuvarna inser att de har blivit påkomna. En serie animerade foton skickas direkt när rörelse upptäcks.
MotionCam är utformad för att övervaka din säkerhet, inte ditt privatliv. Rörelsedetektorer kan inte ta bilder på begäran. Kameran aktiveras endast som svar på ett rörelselarm. Data krypteras under hela överförings- och lagringsprocessen. Du behöver inte titta på kamerorna hela tiden för att veta varför larmet gick.
Detektorn reagerar inte på djur under 20 kg och 50 cm. Men om ett särskilt nyfiket husdjur lyckas utlösa larmet (särskilt en katt), kommer en fotorapport att bekräfta att huset är säkert.
Lägg bara till enheten genom att skanna QR-koden i Ajax-appen.
Strömförsörjning: CR123A (×2), 3 V, upp till 4 år, eller upp till 2,5 år om funktionen för fördröjd inmatning är aktiverad
Ingen garanti på batterier.
Driftstemperatur: -10°C till +40°C
Storlek: 135 × 70 × 60 mm
Vikt: 167 g
Installationsanvisningar finns i Ajax-appen, som öppnas när du skannar detektorns QR-kod under installationen. Enkel installation och anslutning till Ajax Hub.
Tillgänglig för hämtning på
Slut i lager på
Tillagd för jämförelse
Gräns på count_product-produkt uppnådd
Tillagd för jämförelse
Gräns på count_product-produkt uppnådd
{"id":46874647560527,"title":"Default Title","option1":"Default Title","option2":null,"option3":null,"sku":"367308964","requires_shipping":true,"taxable":true,"featured_image":null,"available":true,"name":"AJAX MotionCam PhOD (Picture on Demand) trådlös rörelsedetektor för inomhusbruk med fotoverifiering i vitt","public_title":null,"options":["Default Title"],"price":14816,"weight":0,"compare_at_price":18896,"inventory_management":"shopify","barcode":"4823114014161","requires_selling_plan":false,"selling_plan_allocations":[],"quantity_rule":{"min":1,"max":null,"increment":1}}
AJAX MotionCam PhOD (Picture on Demand) trådlös rörelsedetektor för inomhusbruk med fotoverifiering i vitt
SKU: 367308964
€148,16€188,96
Enhetspris
MotionCam PhOD trådlös rörelsedetektor med fotoverifiering. Foto på begäran.
Fungerar endast med AJAX-kontrollpanelenHub 2 ellerHub 2 Plus.
Skickar verifieringsbild till användaren på 9 sekunder.
Med MotionCam får du reda på den verkliga situationen i hemmet redan innan tjuvarna inser att de har blivit fångade. En serie animerade foton skickas direkt när rörelse upptäcks.
MotionCam är utformad för att övervaka din säkerhet, inte ditt privatliv. Rörelsedetektorer kan inte ta bilder på begäran. Kameran aktiveras endast som svar på ett rörelselarm. Data krypteras under hela överförings- och lagringsprocessen. Du behöver inte titta på kamerorna hela tiden för att veta varför larmet gick.
Detektorn reagerar inte på djur under 20 kg och 50 cm. Men om ett särskilt nyfiket husdjur lyckas utlösa larmet (särskilt en katt), kommer en fotorapport att bekräfta att huset är säkert.
Lägg bara till enheten genom att skanna QR-koden i Ajax-appen.
Strömförsörjning: CR123A (×2), 3 V, upp till 4 år, eller upp till 2,5 år om funktionen för fördröjd inmatning är aktiverad
Ingen garanti på batterier.
Driftstemperatur: -10°C till +40°C
Storlek: 135 × 70 × 60 mm
Vikt: 167 g
Installationsanvisningar finns i Ajax-appen, som öppnas när du skannar detektorns QR-kod under installationen. Enkel installation och anslutning till Ajax Hub.
Tillgänglig för hämtning på
Slut i lager på
Tillagd för jämförelse
Gräns på count_product-produkt uppnådd
Tillagd för jämförelse
Gräns på count_product-produkt uppnådd
{"id":41713219207351,"title":"Default Title","option1":"Default Title","option2":null,"option3":null,"sku":"367308963","requires_shipping":true,"taxable":true,"featured_image":null,"available":true,"name":"AJAX MotionCam PhOD Trådlös rörelsedetektor för inomhusbruk med fotoverifiering Svart","public_title":null,"options":["Default Title"],"price":18896,"weight":0,"compare_at_price":18896,"inventory_management":"shopify","barcode":"4823114014178","requires_selling_plan":false,"selling_plan_allocations":[],"quantity_rule":{"min":1,"max":null,"increment":1}}
AJAX MotionCam PhOD Trådlös rörelsedetektor för inomhusbruk med fotoverifiering Svart
SKU: 367308963
(1)
€188,96
Enhetspris
MotionCam PhOD (photo on demand) trådlös rörelsedetektor med fotoverifiering. Du kan när som helst skicka en begäran om att ta en bild av vad som händer på din egendom.
Fungerar endast med AJAXHubHub 2 ellerHub 2 Plus.
Skickar en verifieringsbild till användaren på 9 sekunder.
Med MotionCam får du reda på den faktiska situationen i hemmet redan innan tjuvarna inser att de har blivit fångade. En serie animerade foton skickas direkt när rörelse upptäcks.
MotionCam är utformad för att övervaka din säkerhet, inte ditt privatliv. Rörelsedetektorer kan inte ta bilder på begäran. Kameran aktiveras endast som svar på ett rörelselarm. Data krypteras under hela överförings- och lagringsprocessen. Du behöver inte titta på kamerorna hela tiden för att veta varför larmet gick.
Detektorn reagerar inte på djur under 20 kg och 50 cm. Men om ett särskilt nyfiket husdjur lyckas utlösa larmet (särskilt en katt), kommer en fotorapport att bekräfta att huset är säkert.
Lägg bara till enheten genom att skanna QR-koden i Ajax-appen.
Strömförsörjning: CR123A (×2), 3 V, upp till 4 år, eller upp till 2,5 år om funktionen för fördröjd inmatning är aktiverad
Ingen garanti på batterier.
Driftstemperatur: -10°C till +40°C
Storlek: 135 × 70 × 60 mm
Vikt: 167 g
Installationsanvisningar finns i Ajax-appen, som öppnas när du skannar detektorns QR-kod under installationen. Enkel installation och anslutning till Ajax Hub.
Hub Plus Jeweller Otrās paaudzes viedais vadības panelis ar četriem sakaru kanāliem, jaudīgu procesoru, trīskāršu RAM ietilpību un divkāršu zibatmiņas ietilpību. Hub Plus uzrauga visu Ajax detektoru darbību un nekavējoties brīdina īpašnieku un apsardzes uzņēmumu.
Hub Plus Jeweller — Ajax viedās drošības sistēmas centrālais vadības panelis
Galvenais apraksts Hub Plus ir Ajax sistēmas centrālā ierīce, kas koordinē pievienotās ierīces un nodrošina saziņu ar lietotāju un apsardzes uzņēmumu. Izstrādāts tikai lietošanai telpās.
Savienojamība un datu drošība Hub Plus prasa interneta pieslēgumu, lai sazinātos ar Ajax Cloud serveri, nodrošinot:
konfigurēšanu un vadību no jebkuras vietas pasaulē,
notikumu paziņojumu pārsūtīšanu,
programmatūras atjauninājumus.
Datu un sistēmas darbības žurnālu glabāšana notiek ar daudzlīmeņu aizsardzību, savukārt datu apmaiņa ar Hub Plus tiek šifrēta un darbojas nepārtraukti 24/7.
Sakaru kanāli Savienojumam ar Ajax Cloud var izmantot:
Ethernet,
Wi-Fi,
GSM tīklu.
Ieteicams izmantot visus kanālus, lai nodrošinātu maksimāli uzticamu saziņu.
Vadība Hub Plus var vadīt ar lietotni iOS, Android, macOS un Windows. Lietotne ļauj nekavējoties reaģēt uz drošības sistēmas paziņojumiem.
Paziņojumu veidi: push ziņojumi, SMS vai zvani (pielāgojami iestatījumos).
Ja sistēma pieslēgta centralizētajam apsardzes pultim, trauksmes signāls tiek nosūtīts tieši uz to, apejot Ajax Cloud.
Atbalstītās ierīces un protokols
Atbalsta līdz 150 Ajax ierīcēm.
Drošais Jeweller radio protokols nodrošina stabilu sakaru darbību līdz 2 km attālumā tiešās redzamības apstākļos.
Automatizācija Izmantojiet scenārijus, lai automatizētu sistēmu un samazinātu rutīnas darbību skaitu:
drošības grafika pielāgošana,
automātisko ierīču (Relay, WallSwitch, Socket) darbības programmēšana,
reakcija uz trauksmi, pogas nospiešanu vai pēc grafika. Scenārijus var izveidot attālināti, izmantojot Ajax lietotni.
Savienotāji un indikācija
LED logo, kas norāda hub statusu.
SmartBracket stiprinājuma panelis (ar aizsardzību pret demontāžu).
Strāvas kabeļa ligzda.
Ethernet ligzda.
Divi micro-SIM sloti.
QR kods.
Tamper poga.
Ieslēgšanas poga.
Kabeļa fiksators.
LED indikācija Hub Plus LED indikācija darbojas divos režīmos:
Hub Plus Jeweller Otrās paaudzes viedais vadības panelis ar četriem sakaru kanāliem, jaudīgu procesoru, trīskāršu RAM ietilpību un divkāršu zibatmiņas ietilpību. Hub Plus uzrauga visu Ajax detektoru darbību un nekavējoties brīdina īpašnieku un apsardzes uzņēmumu.
Hub Plus Jeweller — Ajax viedās drošības sistēmas centrālais vadības panelis
Galvenais apraksts Hub Plus ir Ajax sistēmas centrālā ierīce, kas koordinē pievienotās ierīces un nodrošina saziņu ar lietotāju un apsardzes uzņēmumu. Izstrādāts tikai lietošanai telpās.
Savienojamība un datu drošība Hub Plus prasa interneta pieslēgumu, lai sazinātos ar Ajax Cloud serveri, nodrošinot:
konfigurēšanu un vadību no jebkuras vietas pasaulē,
notikumu paziņojumu pārsūtīšanu,
programmatūras atjauninājumus.
Datu un sistēmas darbības žurnālu glabāšana notiek ar daudzlīmeņu aizsardzību, savukārt datu apmaiņa ar Hub Plus tiek šifrēta un darbojas nepārtraukti 24/7.
Sakaru kanāli Savienojumam ar Ajax Cloud var izmantot:
Ethernet,
Wi-Fi,
GSM tīklu.
Ieteicams izmantot visus kanālus, lai nodrošinātu maksimāli uzticamu saziņu.
Vadība Hub Plus var vadīt ar lietotni iOS, Android, macOS un Windows. Lietotne ļauj nekavējoties reaģēt uz drošības sistēmas paziņojumiem.
Paziņojumu veidi: push ziņojumi, SMS vai zvani (pielāgojami iestatījumos).
Ja sistēma pieslēgta centralizētajam apsardzes pultim, trauksmes signāls tiek nosūtīts tieši uz to, apejot Ajax Cloud.
Atbalstītās ierīces un protokols
Atbalsta līdz 150 Ajax ierīcēm.
Drošais Jeweller radio protokols nodrošina stabilu sakaru darbību līdz 2 km attālumā tiešās redzamības apstākļos.
Automatizācija Izmantojiet scenārijus, lai automatizētu sistēmu un samazinātu rutīnas darbību skaitu:
drošības grafika pielāgošana,
automātisko ierīču (Relay, WallSwitch, Socket) darbības programmēšana,
reakcija uz trauksmi, pogas nospiešanu vai pēc grafika. Scenārijus var izveidot attālināti, izmantojot Ajax lietotni.
Savienotāji un indikācija
LED logo, kas norāda hub statusu.
SmartBracket stiprinājuma panelis (ar aizsardzību pret demontāžu).
Strāvas kabeļa ligzda.
Ethernet ligzda.
Divi micro-SIM sloti.
QR kods.
Tamper poga.
Ieslēgšanas poga.
Kabeļa fiksators.
LED indikācija Hub Plus LED indikācija darbojas divos režīmos: